Göldo MB05C Adapter Bushings

150

Adapterhulzen voor stemmechanieken

  • Voor Vintage KLUSONs
  • 6,3 mm Binnen Ø
  • Standaard
  • 10 mm
  • Finish: Nickel
  • 6 stuks
Leverbaar sinds Juli 2006
artikelnummer 193586
verkoopseenheid 1 stuk
€ 9,90
Incl. btw plus € 5,90 verzending
direct leverbaar
direct leverbaar

Dit product is op voorraad en kan direct verzonden worden.

Informatie over de verzending
Levering ongeveer tussen Dinsdag, 30.04. en Donderdag, 2.05.
1

150 Klantenbeoordelingen

4.5 / 5

U moet ingelogd zijn om producten te evalueren.

Note: Om te voorkomen dat evaluaties gebaseerd zijn op roddel, geruchten of heimelijke advertentie staan wij op onze website alleen evaluaties toe van daadwerkelijke gebruikers die het geevalueerde product bij ons gekocht hebben.

Na inloggen vindt u alle producten die u kunt evalueren ook onder “Product evalueren” in uw klantencentrum.

afwerking

74 Recensies

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
TO
Great product - Just not the right fit
Tiago Oliveira Coelho 21.07.2020
Bought a set of Klusons for my Classic 60's Tele (MIM) to replace the Kluson-style Ping/Fender stock tuners, but the bushings were too narrow for the pre-existing holes. So I found these conversion bushings and thought my problem was solved.
Before anything, I have to say that they're quite good, and feel very solid. A+ for building quality.

However, the holes for the tuners in my guitar is neither 8mm nor 10mm. If you have the same model as I do, either be prepared to enlarge the holes on the headstock to fit these, or just use aluminium tape on the narrow bushings to keep them in place.
afwerking
0
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
t
My bad, they didn’t fit…
tremblox 07.01.2023
These are fine but didn’t fit my application. I’m writing this as a heads-up to others.
Firstly not all tuners, even Gotoh tuners have the same post/shaft diameter. Not even in the same series. Take for example the Kluson-style SD91 series. The units with magnum lock and height adjustable post/shafts - the HAP-M units - have 6mm post diameters. They fit too loosely in these bushings and as a result of the string tension the tuners will get sloppy and wear out prematurely over time.
On the other hand the standard SD91 tuners (no locking, height adjustment) have post diameters of ca 6,25mm (from memory so I might be off by a tad), so that these bushings will be a perfect fit and you’ll enjoy a lifetime of happiness with them.

So in all cases the buyer should check their post diameters carefully before selecting and trying to source the correct bushings. Take care, it’s a jungle out there.
afwerking
1
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
L
Does not fit all Gotoh locking tuners...
LeonardS 25.05.2021
I bought these to install the Gotoh SD-91-05M MG-T locking tuners as the bushing delivered with the tuners were too small for my Fender to fit well.
However, I can confirm that these Göldo MB05C bushings do NOT fit the tuners either as the diameter, like the Fender ones, are simply too small (narrow).
The Göldo MB05C go well with the other Gotoh SD-91 locking tuners, but for those the Fender bushings fitted as well.
The bushings themselves are ok.
afwerking
0
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
BC
Goldo adaptor bushings mb05c
Byrnes C 03.06.2020
did the job perfectly great for fitting vintage style tuners into 10 mil holes without messing up the guitar
straight forward fitting
afwerking
1
0
Evaluatie melden

Evaluatie melden