DiMarzio EP1201PP

253

Push Pull Poti

  • With a long axis, suitable for single cut models
  • 500 kOhm
  • On / off switching function
  • Thread Length: 10 mm
  • Overall length: 20 mm
  • With two nuts and washers
katalógusunkba bekerült: Július 2005
Termékszám 183554
mennyiségi egység 1 darab
Design Push Pull
Resistance Value 500 kOhms
Thread Length 20,0 mm
Tandem Poti No
Push/Push Push/Pull
Solderless No
shaft type grooved
6 333 ft
ÁFÁ-val, plusz 6 900 ft szállítási költség
Azonnal szállítható
Azonnal szállítható

A termék raktáron van és azonnal szállítható

Szállítással kapcsolatos tájékoztató
Csomagfeladás várható időpontja legkésőbb Kedd, 30.04.
1

253 Ügyfelek értékelései

4.5 / 5

A termékek értékeléséhez kérjük, jelentkezz be.

Megjegyzés: Mivel szeretnénk megakadályozni, hogy az értékelések szóbeszéden, hiányos ismereteken alapuljanak, vagy rejtett reklámok legyenek, csak valós ügyfeleink számára tesszük lehetővé értékelések írását, akik valóban tőlünk vásárolták meg a terméket.

A bejelentkezést követően az ügyfélközpontban, a "Termékek értékelése" menüpont alatt megtalálsz minden terméket, amelyet lehetőséged van értékelni.

kivitelezés

108 Vélemények

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
5
5_gadalaiks 03.04.2022
Easy to install and works as it should.
However, I didn’t check the dimensions of this pot, and had to extend mounting hole in the guitar. And you might want to be careful soldering ground wire to the pot. While soldering, I might have damaged the pot and now it can be turned in never ending circle (it still works though)
kivitelezés
0
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
j
Smooth, fast and reliable.
jorgemosquerad 25.06.2021
If you are looking for smooth and fast operation, firm switching, no noise and no loose signal, DiMarzio pots will please you beyond expectations.
I used two on my guitar, a master vol with phase shifting and a tone one with Parallel/series switch. They couldn't work any better, and I consider myself hard to please. I never like anything.
I've had it worst installing other push/pulls in the past, but these DiMarzio were a walk in the park. Although I admit that bigger soldering points would be more confortable.
I will always recommend these pots.
They have nothing to envy CTS or others.
kivitelezés
0
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
B
Nice Feel
Briano 04.12.2013
I used this pot for the "push pull" feature. I was able to split my humbuckers to single coil when the knob was pulled out. It worked great. A really nice feel of torque to it when turning the shaft, and firm soft but solid push and pull action. Very durable. NOTE 500k for humbuckers 250k for single coils.
kivitelezés
5
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
P
Nothing to complain about
Paramite 03.12.2022
These potentiometer aren't abundant, and this is my first one, so i won't compare it to anything. I haven't done the something either, so I don't know if the design is any bad. What I can say for sure, that this thing works perfectly. Sturdy, no cracking or additional noise. I'm using it for about 4 years and nothing has changed, even though our kids like to fiddling with it as well. If you need a switchable potentiometer, don't look any further.
kivitelezés
0
0
Jelentem!

Jelentem!