K obsahu stránky

Racks Rail Set

  • For self-assembly in Thon studio rack 20U 50
  • 2 Rack rails stocked with nuts and rubber inserts
  • Incl. mounting screws and M6x12 rack screws and suitable washers
  • K dostání od Březen 2016
  • Číslo produktu 382627
  • Prodejní jednotka 1 ks
  • 777 Kč
    Všechny ceny vč. DPH
    Na skladě
    Na skladě

    Tento produkt je na skladě a může být obratem odeslán.

    Informace o expedici
    1

    21 Hodnocení zákazníků

    4.7 / 5

    Musíte být přihlášeni, pokud chcete hodnotit produkty.

    Upozornění: Abychom zabránili tomu, že se budou hodnocení zakládat informacích z doslechu, polovičních pravdách nebo skryté reklamě, dovolujeme na našich stránkách hodnotit pouze skutečným uživatelům, kteří u nás vybavení také koupili.

    Po přihlášení najdete také v zákaznickém centru v sekci "Hodnotit produkty" všechny produkty, které můžete hodnotit.

    Zpracování

    10 Recenze

    google translate gb
    Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
    RK
    Not compatable
    R.L. Kok 15.02.2023
    I bought this for my Thon Studio Rack 20U. It was said by an employee that it should be compatable. It's not; it doesn't fit as it should. With that I mean it should start at the bottom and that's where the problem is. It doesn't start there, but at least 1cm above. Besides that it's not so nice to see, it also doesn't have the support from the bottom plate, which is necessary, if the rack is full.
    Zpracování
    0
    1
    Ohlásit hodnocení

    Ohlásit hodnocení

    google translate gb
    Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
    A
    Additional Rack Strip
    Anonymní 24.08.2016
    So I decided to rack mount as much of my gear as I could with the aim of making my music room as neat as possible an minimising the amount of "trip hazard" on the floor as my long suffering wife has the ability to trip up on her own shadow :)

    I wanted to fit a few Adam Hall 87556 sliding rails to the excellent Thon 20U Studio I was purchasing. The sliding rails need mounting at the rear as well as the front so this rack strip was purchased.

    After carefully measuring the required front-rear distance my sliding rails required I marked the rack itself, made some pilot holes and fitted the strip with the screws provided.

    The fitted nuts make mounting equipment at the space you want (rather than the rack forcing you to use specific spacing) is excellent. I normally use a small Philips screwdriver.
    Zpracování
    0
    0
    Ohlásit hodnocení

    Ohlásit hodnocení

    google translate fr
    Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
    SC
    Produit parfait
    Soap Chris 12.09.2021
    Ces rails sont parfaits pour qui désire fabriquer un meuble custom pour son home studio...
    Facile à couper et pourtant vraiment TRES solide.
    Le genre de produit à toujours avoir en stock que ce soit pour du mobilier custom ou des flights...
    Zpracování
    0
    0
    Ohlásit hodnocení

    Ohlásit hodnocení

    google translate de
    Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
    R
    Vorsicht bei den Schrauben
    RayBeeger 08.01.2022
    An sich ein sehr gutes Produkt, die Verarbeitung stimmt! Bei Studio Racks aus Faserplatte (20 mm Wandstärke) ist Vorsicht geboten. Die 15 mm langen Schrauben sind eigentlich perfekt, nur die Faserplatten haben an einigen Stellen das Problem, dass der Druck der Schraubenenden, selbst nach dem Vorbohren, Fasermaterial nach außen drücken können und so die Oberfläche durchdringen ("Aufplatzer"). Man muss also immer die 15 mm Tiefe präzise vorbohren, damit das vermieden wird.
    Zpracování
    0
    0
    Ohlásit hodnocení

    Ohlásit hodnocení