vpme.de ZeroScope

27

Eurorack Module

  • 2-Channel digital oscilloscope, frequency counter and tuner
  • Single, Dual and X-Y modes
  • Time axis adjustable from 10 μs - 10 s (10 microseconds to 10 seconds)
  • Voltage range adjustable from 0.5 - 10 V.
  • Hold mode
  • Power requirement: 30 mA (+12 V) / 10 mA (-12 V)
  • Width: 6 TE
  • Depth: 25 mm
katalógusunkba bekerült: Október 2018
Termékszám 449099
mennyiségi egység 1 darab
Switch Modul No
CV-Editor/VC-Processor No
Tools Yes
Width 6 TE / HP
75 600 ft
ÁFÁ-val, plusz 6 900 ft szállítási költség
Azonnal szállítható
Azonnal szállítható

A termék raktáron van és azonnal szállítható

Szállítással kapcsolatos tájékoztató
Csomagfeladás várható időpontja legkésőbb Kedd, 30.04.
1

27 Ügyfelek értékelései

4.7 / 5

A termékek értékeléséhez kérjük, jelentkezz be.

Megjegyzés: Mivel szeretnénk megakadályozni, hogy az értékelések szóbeszéden, hiányos ismereteken alapuljanak, vagy rejtett reklámok legyenek, csak valós ügyfeleink számára tesszük lehetővé értékelések írását, akik valóban tőlünk vásárolták meg a terméket.

A bejelentkezést követően az ügyfélközpontban, a "Termékek értékelése" menüpont alatt megtalálsz minden terméket, amelyet lehetőséged van értékelni.

kezelés

tulajdonsagok

kivitelezés

20 Vélemények

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
B
Esential tuner for beginner eurorack
Barret707 22.12.2021
I was debating shelling out for the Mordax DATA but there is nothing this little guy doesnt do for half the foot print that id use the DATA for.
kezelés
tulajdonsagok
kivitelezés
1
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
m
Excellent easy to use scope
mentok 10.07.2022
Very easy to use scope, controls are intuitive and integration within patches makes it easy. The V range is nice, I have a full-size scope near the rack that cost four times as much and most of the time end up just using this scope since it is designed _for_ eurorack voltages. Size is a benefit for smaller setups, but does come with the compromise of the smaller screen, but that should be expected. My only issue was the top M3 screws have a longer thread and thus cannot be replaced with knurlies and thus is the one module that requires a screwdriver. However, if installed in the right place (as it is in my setup) one should not need to worry about this after install.
kezelés
tulajdonsagok
kivitelezés
0
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
B
All is clarity
BenjaminRowlinson 14.09.2020
You can see what it does just by looking at it, and what it does it does as well as might be expected, given the tiny, monochrome, OLED. It is a shame that the sample-timing steps are so few and far between – as a result of which you're going to have to tune your sine waves to accommodate the machine if you're hoping to raise any stimulating Lissajous patterns from its XY mode – But stimulate they do. And it turns out that having an oscilloscope within easy reach at all times is even more useful than I'd anticipated. Had this thing on the 40U travelling essentials rack within minutes, right next to the ES-8, and I imagine it'll stay there for quite some time.
kezelés
tulajdonsagok
kivitelezés
0
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
x
Nice 2 channel oscilloscope
xavierxeon 02.05.2021
Only downside is, that the display is rather small, but then it fits in 6HP.

I can highly recommend having an oscilloscope in your modular rack, especially for looking at complex control voltages, for example a mix of LFOs.
kezelés
tulajdonsagok
kivitelezés
0
0
Jelentem!

Jelentem!