Tovább az oldal tartalmához

4-Channel Antenna Splitter

  • UHF Wideband
  • 470 - 608 MHz
  • 614 - 694 MHz
  • 823 - 832 MHz
  • 863 - 865 MHz
  • 2 BNC inputs (9V DC for remote active antennas/boosters)
  • 8 BNC outs
  • 4 DC outlets
  • Format: 19" / 1 U
  • Installation depth: 160 mm
  • Includes power supply, antenna cable and 2 omnidirectional antennas
  • katalógusunkba bekerült: November 2013
  • Termékszám 314056
  • mennyiségi egység 1 darab
  • Device type Splitter
  • Device type Active
  • Frequency range up to - Frequency range from 450 MHz – 950 MHz
  • Width 410 mm
  • Height 45 mm
  • Depth 160 mm
  • Weight 2 kg
78 100 ft
Minden ár ÁFÁ-val
Azonnal szállítható
Azonnal szállítható

A termék raktáron van és azonnal szállítható

Szállítással kapcsolatos tájékoztató
1

288 Ügyfelek értékelései

4.7 / 5

A termékek értékeléséhez kérjük, jelentkezz be.

Megjegyzés: Mivel szeretnénk megakadályozni, hogy az értékelések szóbeszéden, hiányos ismereteken alapuljanak, vagy rejtett reklámok legyenek, csak valós ügyfeleink számára tesszük lehetővé értékelések írását, akik valóban tőlünk vásárolták meg a terméket.

A bejelentkezést követően az ügyfélközpontban, a "Termékek értékelése" menüpont alatt megtalálsz minden terméket, amelyet lehetőséged van értékelni.

kezelés

tulajdonsagok

kivitelezés

159 Vélemények

T
Good for the price with lack of quality
Tamas_Szaraz 02.07.2023
The cable's I got with them are havin very loose connection, One of my QLXD recievers are constantly switching of, or don't even power on till I try to plug it in again. Of course it's not an easy task if it's built in in a rack. The other thing is. It's quite hard to build it in, and fix it, as the hole for the screw and the antenna connector are so close to the eachother, that I only can push it in to the rack railing, if I use a lot of power trying to bend my rack outwards.
kezelés
tulajdonsagok
kivitelezés
0
0
Jelentem!

Jelentem!

Z
Does the job for much less
Zolika_ 23.01.2025
Worked perfectly with Senh EW-D and EW 100 handhelds.
As others have indicated, the DC power cords that came in the package are not suitable for Sennheiser products, so you have to do some tweaking or not use them at all.
The onboard 12V PSU is unregulated (measuring 18V with no load) and since the Sennheiser factory power adapters are regulated (measuring 12V), it may not be a good idea to use the built in PSU. Testing and more infos are needed to make a good decision.
kezelés
tulajdonsagok
kivitelezés
1
0
Jelentem!

Jelentem!

W
Sennheiser G3-mal tökéletes
Winnetou 08.07.2020
4 Sennheiser G3 vevőt használunk színpadon, tökéletesen működik ezzel az osztóval.
10m távolsából már van, hogy gondot okoz a mikroport vétele, főképp ha pár fenék a mikroport és a vevő közé kerül, így az elhelyezéssel kell trükközünk, de lehet inkább pár cápauszony antennát kéne majd lőnünk ehhez a jövőben.
0
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
C
Works flawlessly with Sennheiser wireless diversity gear at a fraction of cost
Clemcohen 26.01.2015
Used this to connect 3 sennheiser Xsw wireless units in a rack plus 1 LD dual wireless mic unit. Please note that the power supply plugs will not work reliably on the sennheiser gear so either you will have to chop off the ends of the sennheiser power supply and adapt the supplied power cables or continue and use the original sennheiser power supplies.

LD power socket fits perfectly, so no problem here but you will need TNC to BNC adapters to connect the antenna to the LD kit which is currently not sold by Thomann. Try Conrad.

Rack kit is included for front mounted antenna. Simple and easy to install.
8
0
Jelentem!

Jelentem!