Rockboard MOD 3 V2 TRS & XLR Patch Bay

17

All-in-one patch-bay for pedalboards

  • Suitable for MOD Slots in RockBoard Pedalboards
  • Compatible with a wide range of other pedalboards
  • Acts as a central access point to the effect setup
  • Establishes clear cable routes to and from the pedalboard
  • Removable front panel for mounting on or under pedalboards
  • 3x 6.3 mm TRS thru
  • 2x XLR thru (male front / female rear)
  • 1x XLR thru (female front / male back)
  • 1x DC 2.1 x 5.5 mm hollow plug thru
  • 1x AC IEC thru (male front / female rear)
  • All connections mirrored on the rear side
  • Dimensions with front panel (W x D x H): 175 x 85 x 47 mm
  • Dimensions without front panel (W x D x H): 160 x 85 x 33 mm
  • Weight: 450 g
  • Includes mounting screws, lock nuts and TX wrench

Note: Register your product at www.w-distribution.de/Warranty and extend the warranty to 4 years.

Notera Register your purchase at www.w-distribution.de/en/Warranty for an extended warranty of 4 years.
Tillgänglig sedan Augusti 2019
Artikelnummer 468599
försäljningsenhet 1 Styck
835 kr
inklusive moms, 99 kr frakt tillkommer
i lager
i lager

Produkten finns i lager och kan levereras omgående.

Information om leveransen
Leverans beräknas mellan Måndag, 6.05. och Tisdag, 7.05.
1

17 Kundbetyg

4.6 / 5

Du måste vara inloggad för att kunna betygsätta en produkt.

Obs! För att undvika att betygsättningen är byggt på rykten eller smygreklam kan bara kunder som har köpt produkten från oss sätta sitt betyg.

Efter inloggningen i kundcentret kan du se vilka produkter som kan betygsättas.

hantverkskvalitet

13 Recensioner

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
T
Total disappointment
TsalerA 30.08.2021
This is the reason of my bad evening.
Bought it to use with Rockboard pedalboard + Rockboard PSU. Looks cool, but that's all.
1. You have to do an screw-thread in the native pedalboard fof this thing by youself! Guys at the factory were very busy)) DIY!!!
2. It's patch-bay for the XLRs! Guess what?) XLR plugs do not fit in to the pedalboard holes!
3. Connected this thing to the native RB PSU. And it's very very noisy! Spend an hour looking whats the problem. It's this thing!!! Unpluged PSU fron this thing. connected PSU bypassing this thing, and it become less noisey!

Summary: This thing is patch-bay for xlrs, jacks and power.
You can not use this with XLRs and Rockboard pedalbords. You Can not use this with Rockboard PSU. This thing is useless. Waste of money(
hantverkskvalitet
2
2
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
LR
I love it!
Love Rockboard 02.06.2021
Makes my board a lot neater and it looks cool too! Perfect for singer/guitarists (like me) or anyone that needs a few xlr ports on top of the normal jacks.
hantverkskvalitet
1
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
CM
Extremely useful passive connections
Cian M. 23.12.2023
Needed this for a pedalboard build a few years back and have used it in a few different routing / signal chains since then.
The other rockboard patchbays look great too but this has the perfect connections for me. The Jack's being TRS for stereo or midi control is great. Makes routing a board with midi controls/foot controller so much neater and easier.
It is also nice for putting my amp foot switch, guitar signal and vocal mic outputs all within a few centimetres. Max setting up at the gig feel like no work at all.
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
J
LOVE IT!!!
JinG 27.01.2024
ease of use and makes my board clean. using it for my rockboard quad 4.2. Thanks thomann!
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension