EMG PA2

76

Preamp / Booster Circuit

For active and passive pickups

  • Suitable for guitars and basses
  • Boost 0 - 20 dB
  • 1 Mini switch circuit
Tillgänglig sedan November 2002
Artikelnummer 158344
försäljningsenhet 1 Styck
818 kr
inklusive moms, 99 kr frakt tillkommer
Tillgänglig om några månader
Tillgänglig om några månader

Denna produkt skickas så snart vi fått in den på lager. Vi kan för tillfället tyvärr inte ange mer exakt leveransdatum.

Information om leveransen
1

76 Kundbetyg

4.7 / 5

Du måste vara inloggad för att kunna betygsätta en produkt.

Obs! För att undvika att betygsättningen är byggt på rykten eller smygreklam kan bara kunder som har köpt produkten från oss sätta sitt betyg.

Efter inloggningen i kundcentret kan du se vilka produkter som kan betygsättas.

hantverkskvalitet

40 Recensioner

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
2
I love this one!
23cm 12.01.2014
This is a great product for giving the guitar the extra bite and mids.

A word of advice: when installing this, don't set the boost at maximum (you'll understand what I'm referring to when you're there). I had it on max and it just made the guitar sound terrible and over distorted (much like the "loudness-mastering" on Metallica's Death Magnetic). Begin at 50%, try the guitar throught the amp and adjust upwards if needed.
Also, think about this before installing it: do you want it to activate when flicking the switch down or up? If you know that, you can put it in the right position from the start.
I wish I had this boost in all my guitars...
hantverkskvalitet
2
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
RS
Great but you need an electronics background ....
ROY STONE 14.01.2020
These are brilliant ..... I find that because of the amount of abuse the wiring of the entire guitar takes, you have be able to fault find electronics to do these & be prepared to repeatedly dismantle Strat guitars, which have no easy access panels, just the complete front panel, meaning removing the strings then a complete rebuild to test it
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
S
Great on-board booster
SteveRob 05.06.2015
I used this to provide the active boost for an Andy Summers replica Telecaster I built.

It did a great job; I moved the trim pot to a full-size pot to control the boost level just like on Andy's guitar.
hantverkskvalitet
1
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
A
Needed it to blend passive and active
Anonym 18.03.2015
I got EM81 bridge and two passive.
So i needed a preamp for passives, because blending passive and active is a bad thing (tested it...horrible).
I used the other side of my selector for passives, and put PA2 at this side's output.
And soldered PA2 output and other side of selector output (EMG81 side) between them.

I put both PA2 and EMG81 at 18V (they handle up to 27V), and a 9V-18V switcher instead of tone knob (metalheads don't need tone knobs :D ).

Nice solution to avoid bypassing passive pickups or replacing them by active single coils.
hantverkskvalitet
1
1
Anmäl recension

Anmäl recension