Rean NYS 207

493

Jack

  • 2 Pole
  • Right angle
  • Height: 6.35 mm
  • Max. Cable diameter: 6 mm
  • Metal housing and plastic kink protection
  • Made by Rean (registered Trademark of Neutrik AG)
Produkt dostępny od Luty 2008
Numer artykułu 201815
Jednostka sprzedaży 1 szt.
Installation No
Mono/Stereo Mono
Angled Yes
Type TS (mono/unsym.)
Plug Jack 6,3 mm TS male angled
5,50 zł
Zawiera podatek VAT, nie zawiera kosztów wysyłki 49 zł
Rabat ilościowy
Cena jednostkowa Oszczędzasz Ilość
5,50 zł 1
5,19 zł 5,6% 50
4,89 zł 11,1% 100
Dostępny w magazynie
Dostępny w magazynie

Produkt jest dostępny w magazynie.

Informacje dotyczące wysyłki
Szacowana dostawa pomiędzy Środa, 8.05. and Czwartek, 9.05.
1

493 Oceny klientów

4.5 / 5

Aby wystawić opinię, należy się zalogować.

Informacja: Aby opinie na temat sprzętu umieszczane na naszej stronie pochodziły jedynie od osób mających styczność z danym artykułem, umożliwiamy wystawianie ocen jedynie naszym klientom.

Opinie można wystawiać po zalogowaniu się w centrum klienta, używając opcji "wystaw opinię".

wykończenie

176 Opinie

google translate gb
Wystąpił błąd. Proszę spróbować później.
AM
Buy this if You need angle connector 6.3mm
Alexandr Mardari 11.05.2021
Buy this if You need angle connector 6.3mm.
I used such designed angled connector named with different brands.
It was always good, never broken. It looks not beautiful, but it is more sturdy than every another design connector in compare. Just does it job well and fits from thin to thick cables. I always use many circles of duct tape above cable attachment point using thin cables, after it is impossible to break the junction.
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
A
Neutrik Quality made in China
Anonimowy 21.07.2014
I have used these plugs for several years now, soldering my own cables for my effects board and making instrument cables. The quality of these plugs is absolutely outstanding for this cheap price. I can hear or see no difference between these plugs and more expensive ones.

The only tricky part is soldering the mass contact to the plug, but with a little bit of excercise (probably after two or three cables), you will do just fine and have good, long lasting plugs for your instruments and effects for barely one euro.

You have to be careful though when using these plugs directly into your amplifier, because of the angled jack it sometims blocks other inputs (for example on my Laney IRT Studio)
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
A
Anonimowy 11.06.2015
Very high quality for a cheap plug. Also very easy to solder, does not need a large amount of heat. The plastic looks weak, but it actualy is not. I have soldered on hundreds of them already onto the cables I make with no complaints. They easily over-last the cables they are soldered on. Highly recommended!!!
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
f
Very reliable
flivver 08.12.2017
If you need angled jack connector, this one is absolutely acceptable. Easy to solder, easy to assemble. So far very reliable.
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie