t
Cheap, cheerful and good
I've used 5 of these on DIY project recently and have used more of them in the past. What I like is that because of the plastic construction you are not forced to tie the cable shield to the (metallic) enclosure housing. As such this let's you "float" your housing if you prefer (e.g. it provides lower noise levels). One has the choice of course to make a wired connection to the case if desired. the noise benefits.
These plastic units feel cheap, and they are. A little care is needed in soldering to them: apply too much heat for too long to the lugs and you'll start to melt the plastic that holds the lugs in place. So take care.
I don't know how these will stand up over the eons. The ones that I've had on commercial pedals and on my own have stood the test of time and I've had no intermittent contacts so they do seem to be robust. I could imagine that kicking a straight jack plug that has been inserted into this socket could cause some problems, (plastic cracking?) but I haven't experienced this yet. By the same token it probably pays not too over tighten the mounting nut as one would surely strip the plastic threads.
So treat it with care and you'll be rewarded with a vast bang for your buck.
These plastic units feel cheap, and they are. A little care is needed in soldering to them: apply too much heat for too long to the lugs and you'll start to melt the plastic that holds the lugs in place. So take care.
I don't know how these will stand up over the eons. The ones that I've had on commercial pedals and on my own have stood the test of time and I've had no intermittent contacts so they do seem to be robust. I could imagine that kicking a straight jack plug that has been inserted into this socket could cause some problems, (plastic cracking?) but I haven't experienced this yet. By the same token it probably pays not too over tighten the mounting nut as one would surely strip the plastic threads.
So treat it with care and you'll be rewarded with a vast bang for your buck.
0
0
Zgłoś nadużycie
HT
Good Fit
This socket was to replace one in my guitar amp which broke after a lead was tripped over and hence cracked the original.
These sockets always seem a bit light and insubstantial, but I have replaced
them a few times before and they don't really need to be built of hardened steel or
titanium as such. This was for a Roland cube and while I couldn't get it on to
the board in the same way the original socket was on, I still got it on in a
sturdy fashion which should hold for long time, assuming of course it doesn't
get yanked again! I had to use the three washers that came with it to get it to fit the amp casing and it looks well, even better in fact than the original which was all black plastic whereas this has a chrome nut.
So it works fine for me and the price is good too
These sockets always seem a bit light and insubstantial, but I have replaced
them a few times before and they don't really need to be built of hardened steel or
titanium as such. This was for a Roland cube and while I couldn't get it on to
the board in the same way the original socket was on, I still got it on in a
sturdy fashion which should hold for long time, assuming of course it doesn't
get yanked again! I had to use the three washers that came with it to get it to fit the amp casing and it looks well, even better in fact than the original which was all black plastic whereas this has a chrome nut.
So it works fine for me and the price is good too
0
0
Zgłoś nadużycie
T
Awesome quality, very durable.
I've always been amazed by Neutrik's products: their quality and durability is top notch and this jack panel socket is no exception.
0
0
Zgłoś nadużycie
J
Good quality, good build
Used it for a diy project, if used correctly, makes the project pretty clean.
0
0
Zgłoś nadużycie
A
Neutrik NMJ2 HC-S
Always useful in an emergency to have in you spares,!
0
0
Zgłoś nadużycie
A
Purchased this and connected it to a guitar speaker in a homemade guitar iso cab i built.It does the job fine,im happy with the product and the service.
0
0
Zgłoś nadużycie
z
Good plug
Good plug. Does it's job.
0
0
Zgłoś nadużycie
s
Good quality Socket
The quality of this product is excellent, nice secure fit and it looks nice too. It has a large black plastic washer trim which covers up any tear-out after drilling your holes, keeping things looking neat. The only issue I have with this is the maximum mounting depth of the socket, it can't be fixed to a case e.g. on a pedal board made with 15mm material, so you have to clear away some material to make it thinner or mount it onto an additional thin plate. Other than that, the product is excellent, does just what I want.
0
0
Zgłoś nadużycie
