Millenium BS-2010

206

Speaker Stand

  • For speakers up to 30 kg
  • Material: steel
  • For flange diameter of 25 mm
  • Foot diameter: 1000 mm
  • Extendable from 119 - 200 cm
  • Weight: 2.6 kg
  • Colour: Black
  • Incl. 25 mm diameter adapter for M6 thread (12 mm long)
Produkt dostępny od Wrzesień 2013
Numer artykułu 320824
Jednostka sprzedaży 1 szt.
Pole diameter 25 mm
2 pieces Set No
Material Steel
Crank No
Ringlock No
Pneumatic No
Feet Tripod
Colour Black
Min. Height 1190 mm
Max Height 2000 mm
Weight per Stand 2,6 kg
Max. Load 30 kg
Pokaż więcej
89 zł
Zawiera podatek VAT, nie zawiera kosztów wysyłki 49 zł
Rabat ilościowy
Cena jednostkowa Oszczędzasz Ilość
89 zł 1
84 zł 5,6% 2
Dostępny w magazynie
Dostępny w magazynie

Produkt jest dostępny w magazynie.

Informacje dotyczące wysyłki
Wysyłka spodziewana do dnia Sobota, 27.04.
1

206 Oceny klientów

4.4 / 5

Aby wystawić opinię, należy się zalogować.

Informacja: Aby opinie na temat sprzętu umieszczane na naszej stronie pochodziły jedynie od osób mających styczność z danym artykułem, umożliwiamy wystawianie ocen jedynie naszym klientom.

Opinie można wystawiać po zalogowaniu się w centrum klienta, używając opcji "wystaw opinię".

montaż

stabilność

wykończenie

84 Opinie

google translate gb
Wystąpił błąd. Proszę spróbować później.
M
Simple stand serving superbly
Michal3806 10.07.2015
as far as stands go, this one will serve you well if you don't put too heavy speakers on top - it's rated to up to 30 kilograms - and is better suited for smaller PA sets.

I purchased this for my Roland Cube CM30 which weighs about 5.5 kilos and is rather small and it feels like a perfect match, not too big, not too small, not too heavy.

Just a word of advice - the 25 mm tube and M6 thread means that for anything else you'll need adapters. I spent a while to get an adapter to the Roland's 3/8 thread but it was my fault, not the stand's. So, to avoid surprises, make sure to check thread compatibility.

But again, if there's a match, this will do the job for a great price.
montaż
stabilność
wykończenie
2
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
Lm
Speaker stand
Luke malta 21.03.2022
Very stable stand and high quality but the top plastic caps are loose and will stuck to speaker when when speaker removed from stand.
montaż
stabilność
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
A
Good value stand for a small speaker
Anonimowy 14.11.2014
I'm using this for a Behringer B205D active monitor that we use as a small PA. The 205D is designer for a mic stand but it felt a bit insecure. This is much more stable and goes a lot higher.

The B205D mounting spigot holds it on a 5/8" mic adaptor leaning back at an angle but I found a microphone table clamp on Amazon which was a short piece of steel channel with a 6mm threaded hole on one flange (for the clamp screw, ideal for the threaded stud on top of the speaker stand cap thingy) and a 3/8" mic adaptor screw on the top. I put it in a vice and bashed the top flange into the right angle to hold the speaker upright, added a 5/8" adaptor and the mounting spigot and it all works well.

So while this is not as light or compact as a mic stand, for most gigs its just right, goes above head height if you need to, and stable enough. If your speaker will fit the 25mm tube, or the 6mm threaded top cap it's fine.
montaż
stabilność
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
K
Does what it's supposed to, breaks easily
Koob 11.04.2017
I wouldn't put speakers up to 30Kg on it :) Fine for small inexpensive speakers, if you don't move a lot. But the bolts break very, very easily.
montaż
stabilność
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie