Göldo E250P

134

Push-Pull Poti

  • 250 kOhm
  • For drawing
  • 2-Way selection switch
  • 6-Pins
Produkt dostępny od Grudzień 2006
Numer artykułu 112185
Jednostka sprzedaży 1 szt.
Design Push Pull
Resistance Value 250 kOhms
Tandem Poti No
Push/Push Push/Pull
Solderless No
shaft type grooved
51 zł
Zawiera podatek VAT, nie zawiera kosztów wysyłki 49 zł
Dostępny w magazynie
Dostępny w magazynie

Produkt jest dostępny w magazynie.

Informacje dotyczące wysyłki
Szacowana dostawa pomiędzy Środa, 15.05. and Czwartek, 16.05.
1

134 Oceny klientów

4 / 5

Aby wystawić opinię, należy się zalogować.

Informacja: Aby opinie na temat sprzętu umieszczane na naszej stronie pochodziły jedynie od osób mających styczność z danym artykułem, umożliwiamy wystawianie ocen jedynie naszym klientom.

Opinie można wystawiać po zalogowaniu się w centrum klienta, używając opcji "wystaw opinię".

wykończenie

51 Opinie

google translate gb
Wystąpił błąd. Proszę spróbować później.
M
Great Pot, good connections, quality feel.
Milodon 14.09.2018
Very good pot. Used to MOD an old guitar humbucker to coil split.
Very easy to install and use, only CON is it is quite tall! you MAY have to remove some material inside the guitar to make this fit in place of a regular pot.

I had to remove 4mm of material from the body inside my Strat to get the scratchplate to fit level again. This is on a standard USA strat in the VOL position, so as you can see if you are less confident with tools/basic luthiery, maybe ask your local guitar shop to fit it in this case.

Overall though, great sturdy pot which will last for years, great solid feel, no interference on the pickups when it is pulled (unlike some) so would reccommend, just check dimensions first!
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
t
teaberryou 30.06.2020
I really like 99% of Goldo products, but this time it's just a pass. Yes, it got the job done, but it feels a bit flimsy compared to the Allparts and Fender versions. After fitting, the axle has a little play in it, which makes the knob go ka-klunk after I release it. It's the first time I'm using it for my builds (because the Allparts version wasn't in stock), so maybe it's just this piece I have, and not all of them. It's not a deal breaker, but if given the choice I'd stick to Allparts for my builds.
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
g
Works Great
gDaddy 14.11.2017
Bought to replace pot in a bass guitar. Works Great.
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
j
nice functional pot!
jerrry 14.09.2018
I took this pot to enable transition between parallel/series connection on humbuckes. It works fine and it gives you a feature nice to have in a guitar, but I think the quality is a little bit cheapish...
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie