Tovább az oldal tartalmához

Audio Transmitter Balun

  • 4 RCA signals transferrable via network cable over up to 670 meters
  • No transmition possible using a hub or the like
  • Operatable only with 2 devices
  • No power supply needed
  • Incl. mounting angle
  • Dimensions: 92 x 70 x 25 mm
  • katalógusunkba bekerült: December 2010
  • Termékszám 252772
  • mennyiségi egység 1 darab
  • Design Box
  • Distribution Type 1in4
  • RJ45 connection female
  • Number of RJ45 connections 1
  • Signal Connection RCA female
  • Number of Signal Connectors 4
  • Connector in RJ45 female
  • Connection out RCA female
10 090 ft
Minden ár ÁFÁ-val
Azonnal szállítható
Azonnal szállítható

A termék raktáron van és azonnal szállítható

Szállítással kapcsolatos tájékoztató
1

24 Ügyfelek értékelései

4.5 / 5

A termékek értékeléséhez kérjük, jelentkezz be.

Megjegyzés: Mivel szeretnénk megakadályozni, hogy az értékelések szóbeszéden, hiányos ismereteken alapuljanak, vagy rejtett reklámok legyenek, csak valós ügyfeleink számára tesszük lehetővé értékelések írását, akik valóban tőlünk vásárolták meg a terméket.

A bejelentkezést követően az ügyfélközpontban, a "Termékek értékelése" menüpont alatt megtalálsz minden terméket, amelyet lehetőséged van értékelni.

kivitelezés

13 Vélemények

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
N
Handy little boxes
NyquistAudio 24.09.2018
Nice sturdy build quality. These were a great solution for me. I'm using these to get extra returns down a single cat5 run for 2 stereo IEMs - going from a console into a Samson S-phone headphone amp to drive Fischer beltpacks in stereo. Unbalanced input on the headphone amp, but these boxes give me a balanced run, and eliminated problems I had with lighting dimmer buzz.
1
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
j
An eye opener
janusM 13.08.2023
This quad ballun really does the job. I used it with 25m of cat6 cable. But when testing (still coiled) I picked up some hum. So I modified it by soldering a ground wire on the casing of the internal RJ45 female connector in on of the 2 boxes. Perfect sound now !
I will also solder myself some balanced cinch-XLR cables (pin 1 unconnected), so that I can send microphone signals through this wiring.
kivitelezés
1
1
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
AJ
saved my life
Abdulla J. 17.07.2020
i used it for long distance (120m) installation audio transfer and it does what it claims nicely.

will buy again.
kivitelezés
1
1
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
S
Not Compatible with the the sssnakeCat Snake 3M series
SEGFAULT 25.11.2024
If you are in the position I was in, wondering how to connect a tape deck "all the way over there" to a mixer "over here" then you may have wondered if you can connect this to a the sssnakeCat Snake 3MC
the sssnake Cat Snake 3MC to get RCA to XLR via a balanced CAT cable.

If you are like me you may have figured out friom the manuals that to have a chance of working you need to open the unit and swap around two connections so the pinouts match.

I am here to tell you that doesn't work. The impedance mismatch between the transformer and the input of your XLR interface is too high for a passive system to overcome. The resulting audio is thin and tinny.

If you buy a second one and use it as intended it works great (although a little pricy for what it is)
kivitelezés
0
0
Jelentem!

Jelentem!