the t.bone CC 100 EW Phantomadapter

36

Phantom power supply adapter

  • Compatible with Sennheiser EW track
  • Replacement part for the t.bone Ovid System CC 100 RC EW (Art.439961)
  • With screwable mini jack socket
  • 3-Pin XLR male connector on the output side
Myynnissä vuodesta Joulukuu 2019
Tuotenumero 472674
Myyntierä 1 kappaletta
Phantom Power Adapter and Feed Units Yes
Phantom Power Adapter Yes
Phantom power No
18,30 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu toimituspäivä Keskiviikko, 26.06. - Torstai, 27.06.
1

36 Asiakkaiden arviot

4.8 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Työnjälki

26 Arvostelut

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
B
A handy power adapter
Bowman2020 03.07.2020
I got this to interface a Sennheiser MKE2 lapel mic to my Focusrite Solo to give me good audio for Zoom and Skype calling.
Works exactly as expected, converting +48V phantom to 5V suitable for the MKE2.
It does stick out an XLR socket a lot so I am using a short XLR jumper cable.
Works great and much cheaper than the equivalent Sennheiser units.
Työnjälki
3
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
LM
Works well so far
Laur Morun 23.09.2022
Bought it for some Sennheiser lapel mikes. So far works perfectly.
Työnjälki
1
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
S
Doesn't work with the Primo EM258
Stozz 03.10.2021
I guess it shouldn't work with it. Just in case if you are wondering.
Työnjälki
1
1
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
s
Well-made, may be adapted
sergio_logic 02.06.2024
The supply adapter is a good transformerless design with a balanced output.

Inside is a Schoeps-style single ended to differential/balanced stage (BJT phase splitter, not JFET, since the JFET for lavaliers is already inside the capsule), followed by one BJT emitter follower for each side of the balanced signal (the balanced output is transistor-based).

May be adapted for other types of microphones by rewiring the 3.5mm connector and/or replacing some resistors. I have changed one to the Sony UWP pinout so I can use with my existing lavalier microphones (all wired for Sony UWP transmitters) into a wired XLR interface.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta