GrooveTech Tools TRC-2 Cheater Trussrod Driver

34

Screwdriver

  • Slotted head
  • Specially made for adjusting vintage truss rods
  • Allows small adjustments without having to detach the neck
  • Oversized handle with rubber inserts
Myynnissä vuodesta Maaliskuu 2012
Tuotenumero 279549
Myyntierä 1 kappaletta
12,50 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu toimituspäivä Maanantai, 13.05. - Tiistai, 14.05.
1

34 Asiakkaiden arviot

4.5 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Työnjälki

20 Arvostelut

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
N
Avoid permanently damaging your vintage bass truss rod nut... use this
Nilo 15.05.2015
It's more or less an expensive screwdriver at first glance. You can also look at things from a different perspective, as I'm assuming the reason you're even considering getting this tool is because you have a £1000+ guitar/bass in your possession at the moment.

Now, with most of the above type instruments, you can constantly have to separate the neck from the body everytime you need to make adjustments to the truss rod. You will know by now that's a pretty risky activity for such a small task. A more precarious alternative is getting any wide flat-head driver and attempt at turning that old, rusty, truss rod nut while the said driver sits at an angle. The last activity basically will render the nut useless in one careless swoop.

The Cheater rod means you don't have to take that chance. It's exactly machined so it sits exactly in the middle of that cross. Suddenly, spending £10 isn't that extravagant anymore.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
m
Nothing special - just a long driver
manofstrat 29.06.2021
I have 3 vintage guitars with truss-rod key in at the heel of the neck. I bought this for those. Not sure why others are happy with it. This 'Cheater' has no cheat! The tip also easily wear off if you're not very carefully insert it to the slot. So, nothing special about the material quality either. The handle has a nice feeling to it.

Any long shaft screwdriver with a big handle can do the same job.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
J
Amazing tool!
Jimbo777 08.07.2017
This special screwdriwer is absolutely a must if you have a Fender Strat/Tele American Vintage series as it will allow you to set the perfect neck relief reaching the trussrod nut without removing the neck from the body.

Probably you'll just need to lower your neck pickup and/or slightly move out the pickguard to have enough room.

No cons, just pros. It's a precious time-saver. Highly recommended.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate it
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
A
Attrezzo utilissimo!
Tuntematon 12.01.2016
Ho acquistato questo prodotto per poter regolare agevolmente il trussrod delle mie chitarre: nei modelli Fender vintage la regolazione avviene alla base del manico ma con questo cacciavite non è più necessario smontarlo. Un risparmio di tempo notevole!
Sono venuto a conoscenza di questo prodotto tramite un video di un Masterbuilder della Fender che lo utilizzava durante una dimostrazione.
Ovviamente è meglio utilizzarlo per piccoli aggiustamenti e ritocchi, mentre per interventi più importanti è sempre meglio smontare la chitarra ed agire in totale sicurezza.
è robusto e ben costruito, la punta sottile e si adatta perfettamente alla vite Fender.


Alessandro
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta