La conținutul paginii

Puresound CPS1420 Custom Pro Wires 14"

4.6 din 5 stele din 216 evaluări ale clienților

Snare strainer / wires

  • Custom Pro Series model
  • for 14" snare drums
  • 20 steel spiral strands
  • Antichoke end plates significantly reduce unwanted snare buzz and allow extremely tight snare tensioning without loss of sound
  • Speed Release straps allow comfortable release of the snare strainer without removing the throw-off mechanism
  • perfect for quickly and easily changing drum heads or wires
  • disponibil din August 2011
  • numărul articolului 269961
  • unitate de vânzare 1 bucată(ăţi)
  • Number Of Snare Wires 20
  • Size 14"
  • Material Steel
166 lei
Toate prețurile includ TVA
în stoc
în stoc

Acest produs e disponibil în stoc și poate fi expediat imediat.

Informații despre livrare
1

216 Evaluările clienților

4.6 / 5

Pentru a evalua produse trebuie să fiţi logat.

Reţineţi: Pentru a preveni evaluările bazate pe zvonuri sau reclame ascunse permitem doar evaluări de lşa clienţii noştri reali, şi care au cumpărat echipamente de la noi.

După logare veţi găsi de asemenea toate articolele care pot fi evaluate Centrul Logare Clienţi.

Impact sonor

Măiestrie

98 Recenzii

google translate gb
Din păcate a intervenit o eroare. Vă rugăm încercați din nou mai târziu.
S
Still as good after 6 years of usage.
Sickorian 23.10.2017
I got this 6 years ago from a friend, and still sounds great. The Easy Release function is really helpful when traveling therefore it does not affect the lifespan of the drum heads. it really was an upgrade from the standard Wires that came with my Snare drum.
Impact sonor
Măiestrie
0
0
semnaleaza un abuz

semnaleaza un abuz

google translate gb
Din păcate a intervenit o eroare. Vă rugăm încercați din nou mai târziu.
RC
A very nice idea
Rudi C. 06.03.2015
I have Puresound snares on my other snare drums and they have invariably been good quality snares. I was intrigued by the strap/quick release system on this model.

The straps have alignment marks. This makes it easier to line-up your snare so it is perfectly centered. The end of the straps have a slot that lets you slide a pin inside (cotter pin). This holds the end plates of the snare in place. It works well, and lets you replace the wire without having to undo the straps. It literally takes under a minute!

The end plates are shaped so they don't choke the snares even at higher tension. The resulting sound was crisper than the stock snares. There was also a reduction in buzz but not a total elimination.

I loved the sound and the quick change idea. I am going to try some other Puresound wires as it makes is so much easier to swap wires around. The only downside was that not all wires are the exact same length (e.g the Equalizer snare was longer than the Custom Pro) so I still needed to adjust the straps, but the swapping was still really quick.
Impact sonor
Măiestrie
0
0
semnaleaza un abuz

semnaleaza un abuz

google translate gb
Din păcate a intervenit o eroare. Vă rugăm încercați din nou mai târziu.
A
Anonim 02.07.2016
When i installed those, I couldn't set up properly my snare for weeks. No matter what I did (tuning, muffling, trying tricks like detune snare bed screws etc) I got excessive buzz and the snares sound was flabby, unless you overtight them. You could hear the snares hit the head right after the batter head sound.
I had to over-tighten the batter head, and I also had to over muffle the reso head with lots of tape, and i also had to overtighten the snares, to get a sound and feel that is just "ok".

The quality seems to be very good, and the fact that you can remove them and reinstall them in 30 seconds is something i liked a lot.
Impact sonor
Măiestrie
0
0
semnaleaza un abuz

semnaleaza un abuz

google translate gb
Din păcate a intervenit o eroare. Vă rugăm încercați din nou mai târziu.
K
Zero quality control
KaroDeLina 10.05.2024
The sound of the wires is OK, the speed release system is pretty cool but... the part where the wires are welded to the plate is catastrophic, the wires are welded unevenly and the end of the wires stick out, so the sharp part of the wire can easily break through the thin bottom snare head, I honed the end parts as I had just put a new snare head on the bottom but I don't think it's something that is acceptable for ''pro wires''.
Impact sonor
Măiestrie
0
0
semnaleaza un abuz

semnaleaza un abuz