On-Stage KS7365EJ

82

Keyboard stand

  • Foldable keyboard stand in Z-shape
  • For 2 keyboards
  • Exterior width: 53 to 91 cm
  • Interior width: 48 to 86 cm
  • Depth of the 1st support: 41 cm
  • Height adjustment of the 1st support: 59 to 92 cm
  • Depth of the 2nd support: 41 cm
  • Height adjustment of the 2nd support: 12 to 30 cm (measured from the 1st support)
  • Angle adjustable in 10° steps
  • Dimensions (folded up): 78 x 58 x 25 cm
  • Rubber pads for a secure hold
Produkt dostępny od Lipiec 2019
Numer artykułu 449542
Jednostka sprzedaży 1 szt.
Keyboard Supports 2
469 zł
Zawiera podatek VAT, nie zawiera kosztów wysyłki 49 zł
Dostępny za 5-7 tygodnie
Dostępny za 5-7 tygodnie

Produkt będzie za niedługo dostępny i natychmiastowo gotowy do wysyłk.

Informacje dotyczące wysyłki
1

82 Oceny klientów

4.4 / 5

Aby wystawić opinię, należy się zalogować.

Informacja: Aby opinie na temat sprzętu umieszczane na naszej stronie pochodziły jedynie od osób mających styczność z danym artykułem, umożliwiamy wystawianie ocen jedynie naszym klientom.

Opinie można wystawiać po zalogowaniu się w centrum klienta, używając opcji "wystaw opinię".

montaż

stabilność

wykończenie

57 Opinie

F
On-Stage KS7365EJ
Freedots 17.01.2024
Stabilny i i bardzo łatwy w obsłudze. Jedyna rzecz, która wg. mnie jest do poprawki to za mała ilość otworów regulujących wysokość dolnego poziomu. Dla kogoś kto gra na siedząco - statyw jest za wysoki. Samemu trzeba "dowiercić" kilka otworów żeby dopasować się idealnie. Poza tym statyw bardzo dobry!
stabilność
wykończenie
montaż
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
i
Best Wallet Friendly option!
iannsk 17.06.2024
Pretty sturdy and and durable stand. Holds my weighty Korg Sv-1 pretty well. Both levels are also pretty wide to accommodate different boards. Screws tighten clamps around the adjustable legs and rods so as to not damage them (unlike those screws that screw on a single point on the legs/rods and damage them).


Do be careful of the screws though, the knobs are made of plastic and may have some sharp edges - a simple sanding and trimming does the trick.

Also, it would be great if there are standard heights settings for the 2nd tier extension. Bottom tier has them but the top doesn’t. Takes a little more effort to get the top tier to level out. Should be an easy fix DIY-ing holes.

All in all a pretty great and sturdy stand for both stage and/or studio use. Definitely recommend!
stabilność
wykończenie
montaż
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
KM
Not good at all , get something else
Kamil M 13.12.2021
Someone really not clever designed this to be honest , 2 synths on it and with a little push the whole stand will tip over to the back , weigh distribution extremely poorly designed. Avoid!
stabilność
wykończenie
montaż
6
2
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
A
Upper tier on the wrong side? Backwards design?
Anonimowy 09.05.2022
It seems to me that this was messed up in the design phase. As several other reviewers have noted, the center of gravity is too far backwards, and the feet stick out way way too far in the front.
I fixed this by flipping the whole thing backwards and using it without the upper tier. Maybe I will try to modify it to install the upper tier flipped to the other side.
stabilność
wykończenie
montaż
3
1
Zgłoś nadużycie

Zgłoś nadużycie