Schatten Design MicroPre Preamp One Channel

12

PCB Preamp

  • Single channel JFET board preamplifier
  • Input impedance: up to 10 MOhm
  • Output impedance: less than 3.5 KOhm
  • Operating time with 9V alkaline battery: 1500 hours (not included!)
  • Operating time with 2 CR2032 button batteries totalling 6V: 750 hours (not included!)
  • Dimensions: 28.5 x 18.5 x 4.5mm
  • Includes belt clip
katalógusunkba bekerült: Május 2020
Termékszám 492749
mennyiségi egység 1 darab
15 790 ft
ÁFÁ-val, plusz 6 900 ft szállítási költség
Azonnal szállítható
Azonnal szállítható

A termék raktáron van és azonnal szállítható

Szállítással kapcsolatos tájékoztató
Szállítás megközelítőleg Csütörtök, 16.05. és Péntek, 17.05. közt.
1

12 Ügyfelek értékelései

4.9 / 5

A termékek értékeléséhez kérjük, jelentkezz be.

Megjegyzés: Mivel szeretnénk megakadályozni, hogy az értékelések szóbeszéden, hiányos ismereteken alapuljanak, vagy rejtett reklámok legyenek, csak valós ügyfeleink számára tesszük lehetővé értékelések írását, akik valóban tőlünk vásárolták meg a terméket.

A bejelentkezést követően az ügyfélközpontban, a "Termékek értékelése" menüpont alatt megtalálsz minden terméket, amelyet lehetőséged van értékelni.

hangzás

kivitelezés

10 Vélemények

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
G
Does the job at a low cost
Guruniverse 30.01.2023
My 40 year old preamp in my Ovation 1618 12 string had gone bad. I found the original Ovation replacement part to be ridiculous expensive. The MicroPre in combination with a stacked potentiometer is a very cost effective alternative, provided you are not scared using a soldering iron.

Installation: instructions are available online. For me a huge plus, cause it allows you to assess it pre-purchase. Diagrams are well documented and showing different installation options (volume only, volume + tone control). If you know how to solder, you can install it. Only downside is that the instructions don not include the tech specs for the volume/tone potentiometers and tone capacitor. Based on the pots sold by Schatten seperately I figured out that both volume and tone pot need to be 500K Ohm log versions. The tone capacitor needs to be 47nF.

Sound: Sounds good to me for live playing. I could not notice a significant difference between the original one and this one.
hangzás
kivitelezés
4
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
m
Go -to Preamp for simple Piezo installation
mjxguerra 27.05.2021
I've tried a number of eBay preamps for piezo installations and for which a Fishman is usually the 1st choice, however for installing a piezo under the saddles of a Vegatrem on a Strat I needed something really compact that would fit in the control cavity. The simple, compact Schatten single channel preamp-on-a-chip is functionally not as clever as a multi-control Fishman installation, but it is super compact, works and blends well with the magnetic pickups.
hangzás
kivitelezés
0
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
MW
Great drop-in solution
Maks Wu 03.08.2023
I've had an ukulele with a broken preamp and a piezo pickup, and this basically solved all my troubles. Great quality, simple installation with proper instructions, and above all, clear sound.
hangzás
kivitelezés
0
0
Jelentem!

Jelentem!

google translate de
Sajnos hiba történt. Kérjük, később próbálkozz újra.
S
Endlich Ruhe und endlich Sound!
SonofEsperanzaSpalding 25.02.2022
Was hab ich nicht alles probiert? ... meinen alten Harley Benton E-Kontrabass mir passivem Piezo zum Klingen zu bringen ... diverse Fishman-, Behringer-, Peaveyvorstufe produzierten vor allem nur eines: "Rauschen!" ... den Empfehlungen eines Bonedo-Testers folgend, habe ich auch noch den Amp gewechselt sprich mir den Ampeg-PF 20 T samt 12er Box zugetan, die passive Elrktronik aus dem Bass raus und den "Schatten Design MicroPre Preamp One Channel" rein, Klangregler weggelassen ... und die Sonne ging endlich auf! ... mein Fazit: also passive Piezobässe, mit diesem Preamp und ein Röhrenbassverstärker ... dann sollte es klappen
Verbesserungswürdig sind die Anschlussmöglichkeiten per Lötkolben (nichts für Anfängerim Basteln!), wieso nicht ein kleines Gehäuse mit Anschlüssen ala Lüsterklemme!
hangzás
kivitelezés
1
0
Jelentem!

Jelentem!