A
Pretty good for the price.
Bought this mainly as storage for expanding rack equipment collection.
Ended up being used for holding a couple of home studio rigs.
Good points are it's solid once you get some gear in it, there are some rails down the centre inside where you could place supports (provided in the package) for any deep rack gear.
I've owned this since 07.09.2013.
Upon delivery it must have been dropped somewhere as the top most hole on one side for the cage nuts was damaged and took some serious bending to get a cage nut to fit it. This didn't really affect the stability or product in any major way.
The castors provided are ok, I found last month that one of them had broken/bent which meant that it would lean. Not a huge problem sice you get castors and static feet for it also. Probable reason it broke was because I keep a gator 8u rack on top of it, which only holds 5 u worth of gear 2x2u and 1 1u piece.
Still if you're using short depth rack gear you could fill both sides of the unit which would be similar in weight. I did expect a bit more from the castors.
When it broke, I just stuck adhesive felt on the bottom of the static feet and it was good to go, however much more immobile.
This thing is HEAVY, I mean really heavy, once assembled it's incredibly difficult to lift (hence the castors).
There's plenty room down the sides of your gear to run cables and power supplies.
Also looks like holes for doors that could be fitted drilled into the top and bottom (door not supplied, or at least mine didn't come with one).
In the pack there are 2 square bits - top and bottom, 2 large rectangles.. The side which are pre loaded with rack strip for M3 (I think) cage nuts (the square ones that you have to insert yourself.
4 static feet, 4 castors
A bag of cage nuts and bolts
A pack of supports for the central strip on each side with nuts and bots to tighten, as well as a hex key tool.
Also supplied are the obvious bolts required to assemble and hex key tool to fit it all. Came with some nice rubberised grommets to fill the holes were the boots go to give a nicer asthetic look.
The central support fits the little supports nicely as once is loosely assembled then you can slot it down and tighten it up.
Rated 4 overall, mainly due to the castor issue which in turn affected the stability.
Couldn't rate the product itself down for the damage during transport as it was smal and just about fixable.
Probably a 2 man job to assemble.
Ended up being used for holding a couple of home studio rigs.
Good points are it's solid once you get some gear in it, there are some rails down the centre inside where you could place supports (provided in the package) for any deep rack gear.
I've owned this since 07.09.2013.
Upon delivery it must have been dropped somewhere as the top most hole on one side for the cage nuts was damaged and took some serious bending to get a cage nut to fit it. This didn't really affect the stability or product in any major way.
The castors provided are ok, I found last month that one of them had broken/bent which meant that it would lean. Not a huge problem sice you get castors and static feet for it also. Probable reason it broke was because I keep a gator 8u rack on top of it, which only holds 5 u worth of gear 2x2u and 1 1u piece.
Still if you're using short depth rack gear you could fill both sides of the unit which would be similar in weight. I did expect a bit more from the castors.
When it broke, I just stuck adhesive felt on the bottom of the static feet and it was good to go, however much more immobile.
This thing is HEAVY, I mean really heavy, once assembled it's incredibly difficult to lift (hence the castors).
There's plenty room down the sides of your gear to run cables and power supplies.
Also looks like holes for doors that could be fitted drilled into the top and bottom (door not supplied, or at least mine didn't come with one).
In the pack there are 2 square bits - top and bottom, 2 large rectangles.. The side which are pre loaded with rack strip for M3 (I think) cage nuts (the square ones that you have to insert yourself.
4 static feet, 4 castors
A bag of cage nuts and bolts
A pack of supports for the central strip on each side with nuts and bots to tighten, as well as a hex key tool.
Also supplied are the obvious bolts required to assemble and hex key tool to fit it all. Came with some nice rubberised grommets to fill the holes were the boots go to give a nicer asthetic look.
The central support fits the little supports nicely as once is loosely assembled then you can slot it down and tighten it up.
Rated 4 overall, mainly due to the castor issue which in turn affected the stability.
Couldn't rate the product itself down for the damage during transport as it was smal and just about fixable.
Probably a 2 man job to assemble.
8
0
Jelentem!
M
Needs to be filled to make it stable
I've had multiple of these racks in different sizes and I've never let down by them. To my taste it's stylish and also very usable product for a good price. These things will last for a very long time in normal use. Just make sure to order some cage nuts and screws to go with it. I reduced one star because of the fact that it needs to be filled with rack gear to make it stable. I give it 4/5 stars.
1
0
Jelentem!
B
Sollid but could use few mm extra width.
Well packed with double carton, it arrived undammaged. Assembling was straight forward, and I did not experience any problems with any of the supplied accessories. No bent nuts as mentioned in an earlier review neither. Fully utalized it is slightly overloaded, but seems to handle the extra weight well. I'll point out thar the rack is used in fixed installation, only to be moved a few feets for behind access.
So far, the only cons I fint worth mentioning is the racks width, which, in case being 19", is pretty tight 19". A few extra mm otside the railing would definately make mounting of equipment much easier.
So far, the only cons I fint worth mentioning is the racks width, which, in case being 19", is pretty tight 19". A few extra mm otside the railing would definately make mounting of equipment much easier.
1
0
Jelentem!
A
Millenium SR-2024
Too high! Yes, it has space to pile up a load of mods.
It needs extra support to make it steady. It is very waggly.
You need to check the connections time to time so your mods don't fall off.
You need to twist it a bit to get the mods installed.
Ugly but works ok.
It needs extra support to make it steady. It is very waggly.
You need to check the connections time to time so your mods don't fall off.
You need to twist it a bit to get the mods installed.
Ugly but works ok.
3
0
Jelentem!
B
Sturdy rack
This rack is actually surprisingly sturdy for the price. I expected it to be slightly flimsy but once the rack gear is mounted it is solid. It also has a very nice system where you can mount brackets in the middle of the rack to help support heavy gear. It makes you feel your gear is more secure and prevents rack rash on the unit below. Highly recommend this one and will be buying another one myself soon!
0
0
Jelentem!
S
Excellent product 👍
It took me ages to decide on which size and make of rack to buy.
I’m very happy I chose this Millenium.👍
It took me ages to decide on which size and make of rack to buy.
I’m very happy I chose this Millenium.👍
0
0
Jelentem!
T
Cheap price, cheap quality!
The metal used in this rack simply can't handle the weight when the rack is filled with equipment. The holes for the wheels gave in, causing the rack to tilt badly. It was sheer luck that I caught it before it toppled over with thousands of euros of equipment in it. The included rack screws/nuts were useless. Every single nut was bent so badly that it was impossibe to force into the rack holes.
I now use the rack as a temporary solution without the wheels/legs installed. It kinda works but is impossible to move without damaging the floor due to sharp metal edges on the bottom plate.
I now use the rack as a temporary solution without the wheels/legs installed. It kinda works but is impossible to move without damaging the floor due to sharp metal edges on the bottom plate.
2
0
Jelentem!
A
If only it had arrived undamaged.
Overall, it's a sturdy enough rack mount and easy to assemble.
Unfortunately, it came very poorly packaged which led to it arriving with 3 of the rails bent. I would return it if there wasn't so much difficulty involved in doing so.
Unfortunately, it came very poorly packaged which led to it arriving with 3 of the rails bent. I would return it if there wasn't so much difficulty involved in doing so.
0
0
Jelentem!
ED
The rack is good
It looks good and it is easy to install. Could use a bit more structure as it inclines a bit, even after installing 6 drawers, but it is pretty tall. Overall, pretty happy with the purchase.
PS. Had some very small damages, but nothing serious.
PS. Had some very small damages, but nothing serious.
0
0
Jelentem!
S
Not very sturdy
This thing cannot handle a full rack of gear. After a short while the rack started leaning forward and the wheels eventually broke from the stress of the weight. I wouldn't buy it again.
1
0
Jelentem!
