Fender Jazz Bass Pre Slotted Nut

107

Original Jazz Bass Nut

  • For 4-string electric basses with a modern 9.5" (241 mm) fretboard radius
  • Material: Micarta (synthetic bone)
  • Width: 38.9 mm
  • Notched
  • Used on the American Standard Jazz Bass and other basses made in the US and Mexico
  • Set of 2
katalógusunkba bekerült: December 2007
Termékszám 139808
mennyiségi egység 1 darab
Unmachined No
Instrument 4-String Bass
9 899 ft
ÁFÁ-val, plusz 6 900 ft szállítási költség
Azonnal szállítható
Azonnal szállítható

A termék raktáron van és azonnal szállítható

Szállítással kapcsolatos tájékoztató
Szállítás megközelítőleg Hétfő, 27.05. és Kedd, 28.05. közt.
1

107 Ügyfelek értékelései

4.6 / 5

A termékek értékeléséhez kérjük, jelentkezz be.

Megjegyzés: Mivel szeretnénk megakadályozni, hogy az értékelések szóbeszéden, hiányos ismereteken alapuljanak, vagy rejtett reklámok legyenek, csak valós ügyfeleink számára tesszük lehetővé értékelések írását, akik valóban tőlünk vásárolták meg a terméket.

A bejelentkezést követően az ügyfélközpontban, a "Termékek értékelése" menüpont alatt megtalálsz minden terméket, amelyet lehetőséged van értékelni.

kivitelezés

47 Vélemények

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
RN
Very well cutted
Rui Nunes 24.09.2021
This pair of nuts are great to replace your jazz bass one. The only downside is that I've used it on a Squier Jazz Bass, which has a flat pocket for the nut, and these ones are curved to the same radius of the fretboard. You can work around it and fill the little gap in the middle, but requires a bit of work. The low E string slot if a bit larger than I expected and a .100 gauge will not fit properly on the sides. I recommend using at least a .105 gauge to make it a snug fit.
kivitelezés
0
1
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
A
Standard Bass Saddle
Anonim 23.11.2015
I needed a new saddle for my Squier Vintage Modified 70s Jazz Bass. Someone put the top 4 strings of a 5 string set on and the saddle produced a lot of buzzing after I stringed it up with a 045 set of strings. The saddle was really easy to install. I just needed to take a hammer and put a screwdriver to the side of the old saddle. Just to make sure the old one would come out easily, I took a scalpel and scored along the edges. After cleaning the saddle slot, the new one fit in perfectly. I just used one drop of super glue just to make sure, it holds securely.

+ perfect fit
+ slotted just right for my 045 strings
+ good sound
+ easy to replace
kivitelezés
0
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
d
Nice replacement nut
dnp41 18.08.2017
this nut fitted my new neck almost perfectly. It's good quality and has the correct widht for my allparts neck. Took me 15 minutes of sanding and filing to get it perfect, but you'd have to do that with almost all nuts. Would recommend to anyone who is looking for a replacement nut. Ow and it comes in a 2 pack so if you'd mess one up, you can have another go at it.
kivitelezés
0
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
s
bit thinner than the stock nut
sibilar 25.08.2021
Everything about this nut seems ok, it's machined fine. The only thing is that is a bit thinner than the stock, but it's workable.
kivitelezés
0
0
Jelentem!

Jelentem!