Doepfer A-189-1

21

Voltage Controlled Bit Modifier Module

  • 16 modes (addition, subtraction, multiplication or division)
  • Manual controller or via CV input (BC - number of shifted bits or SR - sampling rate)
  • Power requirement /: +50 mA (+ 12V) / -20 mA (-12V)
  • Width: 8 HP / 40.3 mm
  • Depth: 60 mm (measured from the back of the front panel)
katalógusunkba bekerült: Szeptember 2008
Termékszám 216457
mennyiségi egység 1 darab
Reverb Ne
Delay No
Multieffect No
Misc. Effects Yes
Width 8 TE / HP
44 290 ft
ÁFÁ-val, plusz 6 900 ft szállítási költség
Azonnal szállítható
Azonnal szállítható

A termék raktáron van és azonnal szállítható

Szállítással kapcsolatos tájékoztató
Szállítás megközelítőleg Szerda, 8.05. és Csütörtök, 9.05. közt.
1

21 Ügyfelek értékelései

4.7 / 5

A termékek értékeléséhez kérjük, jelentkezz be.

Megjegyzés: Mivel szeretnénk megakadályozni, hogy az értékelések szóbeszéden, hiányos ismereteken alapuljanak, vagy rejtett reklámok legyenek, csak valós ügyfeleink számára tesszük lehetővé értékelések írását, akik valóban tőlünk vásárolták meg a terméket.

A bejelentkezést követően az ügyfélközpontban, a "Termékek értékelése" menüpont alatt megtalálsz minden terméket, amelyet lehetőséged van értékelni.

kezelés

tulajdonsagok

hangzás

kivitelezés

12 Vélemények

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
A
Multi-functional tool for audio and cv
Anonim 30.03.2015
I've been putting this module to quite some uses, ranging from normal audio-destruction to CV-arpeggiators.

For audio, the 16 different algorithms create very different tonal colorations, which can be very well used to fatten up your sound when (filtered and) mixed with the original signal.

Used with LFO's it can create interesting patterns which change dynamically by controlling the cv inputs.

Put a noise through this module and control the cv inputs with A/D envelopes to quickly create hard snares, hihats and crashes (pairs good with the wiard noisering) and end off with a clamping vca.

Combine this module in mode 10/11 with a sample&hold and the A-183 offset generator in a feedback routing to make an continuously changing pattern. Add a voltage controlled switch in the feedback path for adding a reset/start-position option.
7
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
WB
A-189-1
Wasp Burgh 08.04.2018
This bit modifier is cool module. It has 16 functions which effect the signal with cv control over it. I like bit crushing LFO's with it making them steppy waves. Plus it works nice on audio signals. I would recommend it if your looking for bit crusher then this will do the job. small hp helps for those smaller cases.
kezelés
tulajdonsagok
hangzás
kivitelezés
2
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
A
Endless bitcrushing and sample rate manipulation fun
Anonim 18.12.2015
The amount of control that Dieter gave us over the bitcrushing and sample rate reduction in this module is astonishing, and all of the algorithms are usable in different situations. My only complaint is that I'd have liked CV control over the algorithm, but I suspect that would sound awful.

Having attenuated CV control over sample rate and bit depth provides endless possibilities for using the lo-fi effects dynamically, especially (ex.) in response to envelope followers, or if you're feeling adventurous, the output of the A-196 PLL...
2
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
JS
Impressive little module for bit reduction type effects
J Synth 04.12.2019
This was well worth buying. It really added alot to the type of sound I was looking for. It has a nice range of effect selections to control how it handles the incoming audio.
kezelés
tulajdonsagok
hangzás
kivitelezés
0
0
Jelentem!

Jelentem!