Thomann SW1045 latched Footswitch

108

Latched Foot Switch

  • Metal
  • With 6 solder lugs
  • Side connections
  • Max. 250V, 2A
  • Installation diameter: 12 mm
  • Case dimensions: 17 x 14 x 20 mm
  • Shaft length: 14 mm
  • Total height: 44 mm
Myynnissä vuodesta Syyskuu 2011
Tuotenumero 271025
Myyntierä 1 kappaletta
6,90 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu lähetyspäivä Tiistai, 30.04. mennessä
1

108 Asiakkaiden arviot

4.7 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Työnjälki

47 Arvostelut

A
Kestävä peruskytkin
Aslak 11.12.2013
Olen rakennellut kitarapedaleja jo jonkin aikaa ja tässä on ollut hyvä jalkakytkin makuuni. Riittävän matala, kestävä, kunnolliset juotoskorvakkeet ja selkeä iso painike. On ollut kovassa käytössä, eikä mitään ongelmaa. Hyvää vastinetta rahoille, mielestäni.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

FF
Broke after barely using it.
Fuzzy Frequencies 24.05.2023
After soldering it in to my wah with schematic that this DOES NOT include, it fell apart as the the thing that keeps it together failed.
It took under 20 switching .
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
KS
Good quality but rather bulky
Kevin S 11.12.2017
Nothing to say against this footswitch, it's well made, sturdy ... and works!

One regret (that didn't cost it any stars though): the bottom part is rather big and the pins would be more convenient if placed towards the bottom and not on the side. The whole thing takes a LOT more room than it should and I always end up having to remove some of the black plastic to be able to bend the pins so that the switch fits properly in my tiny pedals. But doing so makes the pins a bit more fragile, and if you have to solder/unsolder/re-solder one the contact can obviously get messed up ...

So be careful when ordering, do check that you have enough room inside the pedal, or bend the pins but don't unsolder/re-use the switches later on.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
j
jags 13.10.2021
The plastic of the base is very delicate to high temperatures, be careful when you are soldering .

Other than that they are great quality.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta