MXR M 195 Noise Clamp

57

Effect Loop / Noise Clamp Combination Pedal

  • For Electric Guitars and electric basses
  • Noise Reduction -26 dB
  • Eliminates hiss & excess noise from your effects chain with a single threshold Trigger knob
  • 2 Bypass operation modes
  • Adjustable on board
  • Loop off Mode: Effect loop is disabled when the pedal is switched off
  • Loop on Mode: Effect loop is activated when the pedal is switched off
  • 2 Status LED
  • Input and output as well as send and return each has a 6.3 mm jack
  • Sturdy metal housing
  • Operation with 9V battery or power supply 9V DC under Article Nr 409939 (not included)
Myynnissä vuodesta Elokuu 2011
Tuotenumero 260723
Myyntierä 1 kappaletta
Effect Types Noise Reduction
B-Stock 115 € saatavilla
139 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu lähetyspäivä Lauantai, 4.05. mennessä
1

57 Asiakkaiden arviot

4.1 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Käyttö

Ominaisuudet

Ääni

Työnjälki

29 Arvostelut

S
Toimiva kapine
Shamus 13.04.2015
Soitan metallia boostatulla JCM800:lla. Suhina ja sihinä on väistämättä melkoinen. Tällä sai signaalin mainiosti siistittiyä!
Käyttö
Ominaisuudet
Ääni
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
R
Decent pedal
Richmond 06.02.2019
I use this pedal for noise reduction, when guitar is on stand by.
Pros:
* solid build quality.
* effect loop, allows to not include delay, reverb pedals out of the noise gate loop.
* clear instruction manual for proper setup
* decent prices (comparing to Decimator)
Cons:
* limited noise reduction - I would't use it for really high gain scenarios. Was trying to use on JVM410H, on high gain channels and some noise would still go through. Decimator does better on high gain applications.
Käyttö
Ominaisuudet
Ääni
Työnjälki
1
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
J
Simple and reliable!
Juha-Pekka 14.04.2014
I was looking for a simple, durable and reliable noise gate pedal and this one's done the job well! I needed to cut out the feedback and static "hissing" noise of my amp (because of the moderately high gain-settings). For example, when I stop playing all I have to do is to damp out the strings and the M195 kicks in; no more "hissing", feedback etc. You could do that also by changing to a clean channel, but that means more footwork = no thanks.
Käyttö
Ominaisuudet
Ääni
Työnjälki
1
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
F
MXR M-195 Noise clamp: disappointment
Fabio992 18.02.2014
I am disappointed by this pedal as the noise reduction takes a rather long time to come in effect: even a couple of seconds. Besides, the (only) control (for noise threshold) seems to have little or no effect on the pedal behavior. TO note: I have it properly connected (distortion unit in the send-return loop, and delay after this noise clamp) and the other two units in the chain are MXR (Carbon Copy and '78 Badass). I will try out more fiddling with the settings but I cannot see how to make it work as I expect.
Käyttö
Ominaisuudet
Ääni
Työnjälki
0
1
Raportoi ongelmasta

Raportoi ongelmasta