Doepfer A-180-2 Multiples

117

Passive Multi-Port Distributor

  • 8x Interconnected jacks
  • Sockets are divided into 2x quadruple groups; but can also be modified to an eight-multiple (soldering bridge on the circuit board)
  • Width: 2HP
Myynnissä vuodesta Toukokuu 2013
Tuotenumero 315603
Myyntierä 1 kappaletta
Width 2 TE / HP
35 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu lähetyspäivä Perjantai, 26.04. mennessä
1

117 Asiakkaiden arviot

4.8 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Käyttö

Ominaisuudet

Työnjälki

60 Arvostelut

A
A-180-2 multiples
Tuntematon 15.04.2016
Useful module in any modular setup! I bought one but might need more in the future. Only takes 2HP space and doesn't use current.
0
0
Raportoi ongelmasta

Raportoi ongelmasta

m
Great multiples module in small hp
mkok 31.07.2018
Great and space saving multiple module. Great quality
Käyttö
Ominaisuudet
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
A
This mult unit is very cheap but you might need more
Tuntematon 20.01.2016
One thing to note firstly is that despite a lot of what you might read in product information on this and other sites the design of this module has changed slightly. When it is shipped from the factory the middle solder bridge between the two groups of four sockets is not joined, so it is now shipped as standard functioning as two groups of four interconnected jack sockets. If you require an eight-way mult you simply have to join the two groups together at the back of the panel. Just a line of solder will do the job. There's not much to say about this unit, other than the build quality is great - as you would expect from Doepfer - and the unit is competitively priced. I don't see any reason to pay more for equivalent modules from other manufacturers, in which case you would simply be paying for the name. One thing I will point out: if you plan to use this module to multiply CV input to drive oscillators then spend a bit more and get the buffered mult unit A-180-3. This will ensure that voltage is consistent on all outputs, meaning that your oscillators will be easier to get in tune with each other and will track correctly.
3
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
e
Handy utility. Does what it is supposed to do.
emyn 13.12.2021
It mults your signal(s) passively, as promised. And it does so without issues.
Käyttö
Ominaisuudet
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

Liittyvät YouTubesta