asiakastilille sisäänkirjautuminen
Maa ja kieli Country and Language

Doepfer A-100Ad5

27

5V Low-cost adapter

  • Plug adapter for +5 V / 100 mA
  • Can be used in place of a 5 V power supply
  • For Doepfer modules requiring +5 V: e.g. the A-113,190 or 191
  • Can be plugged into a free socket on the bus board
  • The current is taken from the 12 V supply
Description Electronic Component
Tuotenumero 166503
14,90 €
Sisältää ALV:n. Ei sisällä 12 € toimituskuluja
Samantien saatavilla
Samantien saatavilla

Tämä tuote on varastossa ja voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu toimituspäivä Torstai, 28.10. - Perjantai, 29.10.
1
257 Myyntisijoitus

27 Asiakkaiden arvostelut

5 21 Asiakkaat
4 5 Asiakkaat
3 1 Asiakas
2 0 Asiakkaat
1 0 Asiakkaat
4.7 / 5

Työnjälki

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
S
May the force be with you... exactly 5 volts.
Stephen662 15.07.2013
Needed this to supply 5 volts to some of the modules in my Doepfer case. Yes, some modules (usually logic modules) need 5v to work, and this is what you need.

Simply plugs into the rail that you need to supply the 5v on - if you have 5v modules all over your rack you will need to instal one on each rail as required. Job done. Works a treat.
3
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
A
You might not think you need this but you probably will
Tuntematon 20.01.2016
This little adaptor will allow you to run anything which requires a +5v power supply on one power rail of your modular case. I bought it because it was required for an oscillator which I purchased, but it can have many applications. My next use for it will be to power LED lights to illuminate my modular in gig situations. You simply connect the adaptor to a spare connector on the rail which you will need it, and then you have +5v power available for all the other connectors on that rail. My one reservation is that this could have been a little bit cheaper for what it does, or alternatively Doepfer could just build this provision into their modular cases as standard. After all a P9 case, for example, is not cheap and when you have spent that amount of money you kind of resent having to buy this.
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
A
Andrew463 06.12.2014
Tough one to rate as it's just a plug... but if you have products from Mutable Instruments and others that require 5-Volt power it's a necessity for a Doepfer rack. It couldn't be any simpler to use, just plug it in and away you go.

Again, good value too.
1
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
HT
Get it for those hungry modules.
Harry Turner 02.11.2019
The Sub Harmonic Generator requires this.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

Neuvonta