Adam Hall STRS6U Rack Stand 6U

149

Rack Stand 6U

  • Black
  • Threads for M5 screws
  • 12 Screws included
  • Weight: 1.6 kg
Myynnissä vuodesta Helmikuu 2012
Tuotenumero 277570
Myyntierä 1 kappaletta
Type Tabletop Stand
Height 310 mm
Weight 2,2 kg
22,90 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu lähetyspäivä Perjantai, 10.05. mennessä
1

149 Asiakkaiden arviot

4 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Vakaus

Työnjälki

79 Arvostelut

V
Good standard rack
Vilhonatus 12.05.2022
Good standard rack for suit your needs for 3 units.

My only complaint is the angle. Due to that, the lowest slot is suitable for powerstrip or patchpanel etc. but due to angle, most rack model audio equipement is too deep for it.

Also first slot on the top is designed for rack light like <a class="article link" href="https://www.thomann.de/fi/adam_hall_87451_pro_c_led_rack_light_mc.htm">Adam Hall 87451 Pro C LED Rack Light mc</a>, so it really has slots for 4 units, 1 racklight and 1 patchpanel or powerstrip.

Other than that the build quallity is very good. parts won't bend easilly (even the support pipe on top is surprisingly sturdy), rubber feets are top notch, it almost feels like my rack is bolted to my table.

Overall good rack, but due to the design I would recommend this to be used for powerstrips, patchpanels etc. because it really seemes like that's what this is for, to be left on the floor or stage with some patch panels or powerstrips or cable management.
Työnjälki
Vakaus
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
G
6U Rack stand that is really only a 4U
Gerard1742 14.09.2015
This stand is a decent stand. It is tough and seems to be built well. The metal seems of good quality for sure. However, the stand has a big down side in regards to its function. There is a support strut that goes across the top of the stand. Well this pretty much rules out the chance of installing any 1u rack device. You just cannot avoid this strut. So your robbed of basically the top 1u slot. The next thing that robs you of another 1u is the fact that the stand is too low to allow the bottom 1U space to be filled. As others have said this stand is more like a 4U.

I guess it's down to poor design that two 1U slots are made redundant. So be careful in your choice of stand. Luckily there was no great urgency for me to have 6U, I just chose this stand for the extra space available if I need it perhaps in the future.

One other thing, which is not a big deal, but it would have saved some time. There is no guide on how to setup the stand. It is straight forward but a simple diagram would have helped. Must things come with set up diagrams, it's not a big ask to have had one supplied. I had to go onto the website again to see what the stand looked like so I didn't install the strut and the rear bar in opposite positions.

Performance wise the stand holds up well. It seems quite sturdy and so long as it's not abused it will hold your rack gear no problem. Obviously it will not take a huge 4U rack PA as this would just be too heavy. But it will hold your 1 U preamps and EQs and noise gates with no issues and it sits very stable on a flat surface such as a desk or cabinet.
Työnjälki
Vakaus
6
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
I
Well Made Rack
ImAndi 05.05.2015
Hey, babe. Nice rack!

Thanks, it's the Adam Hall STRS6U and boy is it sturdy! Fill it up and it's even sturdy enough to use the top horizontal bar as a handle, depending on the weight of course.
Työnjälki
Vakaus
3
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
B
I confirm the other reviews
BattleAngel 02.08.2021
Screw holes are badly made. I had 2 screw holes totally unusable. I would need to drill and remove metal elements that are blocking screws from a normal screwing. So immediately, 1U is totally unusable.
If not that, then top 1U would be actually totally usable on the contrary to other comments. This top bar/rod doesn't need to be mounted.
The stability is excellent. After mounting just 1U unit, it has become stable already. Now when I have 3U filled, there's nothing to complain. It sits on my desk, and even that small part of it is beyond the desk, it's super stable.
I bought this rack for two devices: Focusrite Scarlett 18i20 (second from the top) and Behringer Model D on the bottom (but not at the very bottom because holes in the rack ears didn't let me put it lower.
Työnjälki
Vakaus
0
0
Raportoi ongelmasta

Raportoi ongelmasta