Doepfer A-156

Dual QuantiserThe A-156 Module is a dual control voltage quantiser. A quantiser converts a continuous input control voltage in the range of 0 ... 10V into a stepped output voltage in the same voltage range. The possible steps in the A-156 are not restricted to the usual half-tone grid (ie gradation in 1 / 12V steps) but also allows other scales of the grid such as the major scale, minor scale, major chord , Minor chord, fundamental fifth and the inclusion of sixth or seventh in the chords. The voltage values ​​at the input are only converted into discrete voltages at the output, which meet the selection criterion for the permissible voltage grid (for example a minor seventh chord). The operating mode for Quantiser 1 is set with 3 tilt switches with center position. The Quantiser 2 is fixed to the half-tone grid.

For each of the two Quantisers there is a control input (CV In), a control output (CV Out), a trigger input (trig in) and a trigger output (trig. Out). If no signal is present at the trigger input (socket open), the quantisation is carried out continuously. If, however, a square-wave signal is applied there (from an LFO or the MIDI-SYNC interface for example), the quantisation is always performed only at the rising edge of the trigger signal. The quantisation process can thus be synchronised with other processes on demand. At the trigger output, a pulse appears whenever a quantisation (or a step change in the output voltage) occurs. For example, an envelope generator (ADSR) can be started.

In addition, the module has a common transpose input, which can be added to both quantisers and is quantised in a halftone grid. A typical application for this is to transpose a quantized sequence (generated by the A-155) with a second control voltage (from the MIDI CV interface for the example).

  • Quantisation of a tone sequence from the A-155 into a fixed grid (halftones, only major scale, minor scale only)
  • Quantise the control voltage of a Trautonium manual A-198, Theremin A-178 or Light-to-CV module A-179 to get always half-tones, scales, or chord sounds
  • Arpeggio-like sound sequences with LFO, Random, Noise, ADSR etc. as input voltage --!>

Euro Rack Module

  • Bi-directional control voltage quantiser
  • Converts continuous input voltage into step output voltage
  • Euro rack format
  • Width: 8 HP
  • Depth: 55 mm
  • Power consumption: +50 mA (+ 12V)/ -10 mA (-12V)

These are other customers' choices:

Customers who looked at this item have bought these:

Doepfer A-156
41% bought this exact product
Doepfer A-156
Available immediately
Available immediately

This item is in stock and can be dispatched immediately.

Standard Delivery Times
118 € Add to Cart
Doepfer A-149-1
9% bought Doepfer A-149-1 109 €
Doepfer A-184-1
9% bought Doepfer A-184-1 98 €
Doepfer A-185-2
9% bought Doepfer A-185-2 68 €
Doepfer A-151
8% bought Doepfer A-151 58 €
Our most popular Various Modules
33 customer ratings:
  • 5
  • 4
  • 3
  • 2
  • 1
4.7 / 5.0
  • handling
  • features
  • quality
19 written ratings Read all reviews
Total

Doepfer A-156 Quantiser

Blair, 04.04.2014
I have the Doepfer A-149 module which generates stored and quantised random voltages. This is great, but soon I found myself looking for a module which would take the output of the A-149 and restrict it to play notes from recognisable scales, such as major and minor ones. I also wanted to create arpeggios which included only notes from certain chords. Research showed that I needed to get a control voltage quantiser, which would select from the random collages only those values that would play notes from chords or scales I had selected.

I bought the A-156 Dual Quantiser after I had checked out much more expensive versions from other manufacturers. The A-156 does not have all the 'bells and whistles' of its more expensive competitors, such as programmable scales and memories. however these devices are at least twice as expensive as the A-156, and I was not looking for extra functionality. A key feature of the A-156 is that it is a dual quantiser - in effect two devices in one. However, the second quantiser defaults to generating semi-tone scales only. This can be changed by changing the position of a jumper on the main circuit board. After that, both quantisers offer the same features, such as notes from a chosen scale or arpeggio playing a certain chord.

The A-156 also includes trigger outputs, which will send a gate signal each time a new note value is generated. This is very useful for 'shaping' the sound, such as triggering a low pass gate to open each time a note is created by the A-156 and played by a VCO.

Are there any shortcomings? Not really. For the price this module performs incredibly well, and it easy to operate. My one suggestion is that the jumper that links or separates the two quantisers, should be replaced by a 2-way switch on the module's front panel.

Great module, highly recommended.
Helpful · Not helpful · Report review
Report rating…

Do you believe this rating to be inaccurate or unacceptable for some reason?

Send report
Total

simple, inexpensive and essential

31.10.2016
Soon after I started my modular system I realised that a quantizer was going to be essential.
Although this is a simple quantizer (compared with some on the market) it proved to be just what I needed and affordable ...and then I discovered how much more it could be.
Two quantisers in one module is great as you can produce a bassline and arpeggio and then transpose the whole thing playing notes from a keyboard.
The trigger functions can produce some interesting effects. For example send a sine LFO (offset to be in the positive range for the quantizer) to one of the inputs and take the trigger out and you get a speeding up and slowing down trigger sort of like the rhythm of a perpetually boucing ball.
I also often use the switches as performance controls shift your whole piece from minor to major or to introduce a 6th or 7th.
The only improvement I would suggest would be LEDs to show the state of the output triggers ...but I'm maybe too fond of flashing lights!
Helpful · Not helpful · Report review
Report rating…

Do you believe this rating to be inaccurate or unacceptable for some reason?

Send report
Show variations of this product
Doepfer A-156
(33)
Doepfer A-156
to the product
118 €

Dual QuantiserThe A-156 Module is a dual control voltage quantiser. A quantiser converts a continuous input control voltage in the range of 0 ... 10V into a stepped output voltage in the same...

  • Module: Yes
  • Empty Rack, Or Housing: No
  • Basic System: No
  • Accessories: No
Doepfer A-124 Wasp Filter SE
(34)
Doepfer A-124 Wasp Filter SE

Wasp Filter Special edition, Special 12 dB multimode filter, Circuit technology of the "EDP Wasp", Black front, Yellow pot caps, Width: 8 HP, Depth: 45 mm, Power requirements: +30 mA (+12 V)/-10 mA...

  • Module: Yes
  • Empty Rack, Or Housing: No
  • Basic System: No
  • Accessories: No
Doepfer A-110-1
(62)
Doepfer A-110-1
to the product
138 €

Standard VCO for Modular System A-100Module A-110-1 (VCO) is a voltage controlled oscillator. The A-110-1 produces frequencies in a range of about 8 octaves, of which four waveforms are available...

  • Module: Yes
  • Empty Rack, Or Housing: No
  • Basic System: No
  • Accessories: No
Doepfer A-138s Mini Stereo Mixer
(7)
Doepfer A-138s Mini Stereo Mixer

Mini Stereo Mixer 4-in-2 mix module in Eurorack format, Four inputs with attenuator and pan control, plus two 3.5 mm mini jack outputs, Width: 8 HP, Depth: 30 mm, Power requirements: +10 mA (+12 V)...

  • Module: Yes
  • Empty Rack, Or Housing: No
  • Basic System: No
  • Accessories: No
Doepfer A-160-2 Clock Divider II
(12)
Doepfer A-160-2 Clock Divider II

Frequency divider For clock/trigger/gate signals, Width: 4 TE/ 4 HP / 20 mm

  • Module: Yes
  • Empty Rack, Or Housing: No
  • Basic System: No
  • Accessories: No
Doepfer A-100 LC1 Low Cost Case
(5)
Doepfer A-100 LC1 Low Cost Case
to the product
118 €

Case for Eurorack Modules Integrated power supply A-100SSB: +12 V / 380 mA, -12 V / 380 mA, To 48 TE shortened A-100LC3 version, Built-in bus board with 8 module slots, Casing made of raw wood -...

  • Module: No
  • Empty Rack, Or Housing: Yes
  • Basic System: No
  • Accessories: No
Doepfer A-180-2 Multiples
(60)
Doepfer A-180-2 Multiples

Passive Multi-Port Distributor 8x Interconnected jacks, Sockets are divided into 2x quadruple groups; but can also be modified to an eight-multiple (soldering bridge on the circuit board), Width:...

  • Module: Yes
  • Empty Rack, Or Housing: No
  • Basic System: No
  • Accessories: No
Doepfer A-180-3 Dual Buffered Multiple
(11)
Doepfer A-180-3 Dual Buffered Multiple

Synthesizer module Double buffered 1-in-3 multiple, For buffering and duplication of CV and audio signals, Width: 4 TE / 4HP / 20.0 mm

  • Module: Yes
  • Empty Rack, Or Housing: No
  • Basic System: No
  • Accessories: No
Doepfer A-119
(37)
Doepfer A-119

External Input / Envelope FollowerModule A-119 is used to integrate external audio signals into the system A-100, and includes the components pre-amplifiers, envelope follower and a comparator. The...

  • Module: Yes
  • Empty Rack, Or Housing: No
  • Basic System: No
  • Accessories: No
Doepfer A-132-3
(23)
Doepfer A-132-3

VCA Switchable characteristic between linear and exponential, Audio and CV signals can thus be optimally processed, Width: 8 HP, Depth: 50 mm, Power requirements: +30 mA (+12 V)/-30 mA (-12 V)

  • Module: Yes
  • Empty Rack, Or Housing: No
  • Basic System: No
  • Accessories: No
Doepfer A-140
(55)
Doepfer A-140

ADSR Envelope Generator The module A-140 is a envelope generator and since it delivers control voltages, belongs to the modulation-modules. As soon as the ADSR is triggered at gate-input, it...

  • Module: Yes
  • Empty Rack, Or Housing: No
  • Basic System: No
  • Accessories: No
Doepfer A-138b
(52)
Doepfer A-138b

Mixer with Logarithmic Potentiometers Primarily suitable for audio signals, Width: 8 HP, Depth: 35 mm, Power requirements: +10 mA (+12 V) / -10 mA (-12 V)

  • Module: Yes
  • Empty Rack, Or Housing: No
  • Basic System: No
  • Accessories: No
118 €
Free shipping incl. VAT
Available immediately
Available immediately

This item is in stock and can be dispatched immediately.

Standard Delivery Times
Share this product
Your Contacts
Phone: +49-9546-9223-30
FAX: +49-9546-922328
Offers include 21% Belgium VAT and are valid as long as stocks last. Shipping costs to Belgium are 2,50 EUR, free shipping on orders above 49 EUR. Please click here for international Shipping rates. We do not accept liability for typographical errors or inaccurate information of any kind. *RRP = manufacturer's / distributor's recommended retail price in Germany
Harley Benton Fusion-HSH Roasted Maple Slate Digital ML-2 DPA 4066-OC-A-F10-LH Slate Digital ML-1 IK Multimedia UNO Synth JHS Pedals The Bonsai Hercules Stands HCGS-414B+ Guitar Stand Zynaptiq Intensity Clavia Nord Music Stand V2 Tech 21 DP-3X Solar Guitars S2.6C K&M 17650 Guitar Stand
Recommended
Harley Benton Fusion-HSH Roasted Maple

Electric Guitar Ergonomically shaped mahogany body, "Ultra Flame" flamed maple veneer top, Matching headstock, Bolt-on neck from "roasted" Canadian flamed maple, "Roasted" maple fretboard, Neck shape: Modern C, Clay Dot fretboard inlays, 24 Medium jumbo stainless steel frets, Nu-Bone...

to the product
399 €
(2)
Recommended
Slate Digital ML-2

Small Diaphragm Condenser Microphone For Slate Digital VRS8 Thunderbolt audio interface, similar linear and flat frequency response to the Slate Digital ML-1, Allows microphone placement that is difficult or impossible for a larger microphone, Side mounted pad switch -...

to the product
159 €
Recommended
DPA 4066-OC-A-F10-LH

DPA 4066-OC-A-F10-LH, d:fine CORE 4066 Omni Headset Mic, professional headset microphone with removable and adjustable neck holder for left or right-sided use. Omnidirectional, 20Hz-20kHz with 3dB boost between 8-20kHz, 144dB SPL max.,TA-4F Switchcraft connector for Shure Transmitter . beige, Great...

to the product
719 €
Recommended
Slate Digital ML-1

Large-diaphragm condenser microphone Neutral ML-1 condenser microphone that can be combined with VMS hardware and software, Optional Neutral VMS preamp ensures minimal sound-colouration (not included!), Via VMS plug-in software, you can completely change the sound characteristics even after recording,...

to the product
849 €
Recommended
IK Multimedia UNO Synth

Monophonic analog synthesizer with step sequencer, arpeggiator and effects section Classic setup with 2 VCOs and noise generator, multimode filters, amps, 2 envelopes and LFO, Waveform VCOs Triangle, sawtooth and variable pulse width rectangle, Multimode filter with 12 dB...

to the product
229 €
(1)
Recommended
JHS Pedals The Bonsai

Effect Pedal Overdrive, 9 Tube Screamer Overdrive modes, 5 Classic TS circuits and 2 popular mods, Analogue operation, True bypass, Volume, sustain and tone controls, 9-Way rotary control to select between Tube Screamer modes (OD-1 / TS-808 / TS-9...

to the product
259 €
Recommended
Hercules Stands HCGS-414B+ Guitar Stand

Hercules Stands HCGS-414B +, AGS PLUS Guitar Floor Stand for All Electric Guitars / Electric Basses / Acoustic Guitars/Mandolinen/Banjos and Ukulelne, Auto Grab Holder automatically secures the instrument from falling out, (for standard widths of 40-52 mm) with improved foam...

to the product
44 €
Recommended
Zynaptiq Intensity

Zynaptiq Intensity (ESD); enhancer plugin; innovative algorithm increases detail, clarity, density and loudness of any audio signal; suitable for single tracks, groups, mixbus or mastering; easy to us clearly arranged user interface; additional soft-knee saturating limiter at the output stage;...

to the product
148 €
Recommended
Clavia Nord Music Stand V2

Clavia Nord Music Stand V2 - music stand for Nord C2 Combo Organ, Nord C2D, Nord Electro 3 HP, Nord Electro 4 HP, Nord Electro 5 HP, Nord Electro 6, Nord Piano 88, Nord Piano 2 HA88, Nord Piano 2...

to the product
69 €
Recommended
Tech 21 DP-3X

Preamp for bass dUg Pinnick signature model, Controls: volume, chunk, high, mid, low, comp, drive, Gain switch, Mix button, Chromatic tuner, XLR DI output, TRS input / output, Headphone output, Dimensions (W x D x H): 19.7 x 6.4...

to the product
299 €
(1)
Recommended
Solar Guitars S2.6C

Electric Guitar Body: Mahogany, Neck: Maple, Fretboard: Ebony, Neck profile: C, 24 Super jumbo frets, Graphite nut, Nut width: 43 mm, Scale: 647 mm, Pickups: 2 Duncan Solar humbuckers, Grover 18:1 locking machine heads, Colour: Carbon matte

to the product
699 €
(2)
Recommended
K&M 17650 Guitar Stand

Guitar Stand - Carlos Tall A-frame design, Can be folded flat, Support arms include protective felt pads, Suitable for guitars with nitrocellulose lacquer finishes, Neck lock (Security Lock), Colour: Black, Support depth: 125 mm, Dimensions: 410 x 515 mm,...

to the product
69 €
Feedback Found an error or want to give us feedback about this page?

We're looking forward to hearing from you and aim to solve any problems as soon as we can.

Please leave a comment. Please enter your e-mail address.