TAD Bias Master BM4

82

Measuring Device For Bias

  • Four octal socket adapters
  • For the control of the retirement
  • At 6L6GC, 6550, EL34, 6V6 GT, 5881, KT88, KT66, KT90, KT100, 7027A
  • With illuminated display
  • Made in Germany
In catalogo dal Dicembre 2003
Numero di articolo 166243
Unità incluse 1 Pezzo
€ 199
Spedizione gratuita, incl. IVA
disponibile
disponibile

Questo prodotto è disponibile e può essere spedito immediatamente.

Informazioni sulla spedizione
1

82 Valutazioni dei clienti

4.5 / 5

Devi effettuare il login per poter lasciare una recensione.

IMPORTANTE: Per evitare di inserire informazioni per sentito dire, non complete o sbagliate, permettiamo di dare un giudizio delle attrezzature solo ai nostri clienti che hanno comprato la merce direttamente da noi.

Dopo il Login trovi nella tua area cliente troverete sotto la sezione "Giudica i prodotti" tutti gli articoli ai quali potrete dare un giudizio

Qualità

44 Recensioni

A
Perfect tool for easy biasing
Anonimo 17.05.2016
I bought this tool for my Blackstar Series One 104 EL34. I'm not an amp tech, but I've already done two successful biasing with it. The most important thing is knowing your new tubes, reading their specification usually mentioned on the producer website, and follow the procedure written on the manual. You have to be careful anyway, since there's dangerous currents inside any amplifier.
Qualità
1
0
Segnala un abuso

Segnala un abuso

A
TAD Bias Master
Andrea72 23.01.2021
Semplice da usare, ben costruito e utile.
L'ho utilizzato per tarare le valvole di un deluxe custom deluxe '68 ed è stato molto semplice, le istruzioni sono essenziali ma sufficienti per utilizzare adeguatamente lo strumento.
Soddisfatto.
Qualità
0
0
Segnala un abuso

Segnala un abuso

google translate gb
Sfortunatamente si è verificato un errore, La preghiamo di riprovare più tardi.
R
TAD Bias Master BM4
Robert814 09.03.2014
This model comes with 4 octal probes, but I ordered 2 noval probes as well so that I can set up EL84's as well as 6V6's and 6L6's etc.
WARNING! - There are no instructions! - If you don't know what you are doing, don't try to use this unless you have a friendly tech to show you. You can download them from the TAD site, only 2 sides of A4 folded into a leaflet. Very basic instructions.
The probes each contain a 1 ohm resistor in the cathode lead, so they are measuring total cathode current (anode + screen grid). Circuit schematic diagrams usually state a bias Voltage (e.g. -37Volts) rather than current. This is a good starting point, but then you need to find the valve manufacturer's specifications from their data sheets. Then you can balance up each side of the push-pull stage.
The readout on the unit is 00.0 mA to presumably 99.9 mA.
A "Chicken head" pointer knob selects each of the 4 individual valves, or the OFF position.
It's really simple and easy to use (as another reviewer has said) and you don't have any high voltage connections to make through a test meter. The real skill is knowing just where to set the current level, which is of course different for each and every valve type and can be slightly tweaked for your preferred sound.
Qualità
4
0
Segnala un abuso

Segnala un abuso

google translate gb
Sfortunatamente si è verificato un errore, La preghiamo di riprovare più tardi.
AS
It`s okay
Amateur Slash 27.05.2017
Unfortunatelly there aren?t too many options on the markt to choose from.
Would have preferred a tool that can measure the plate voltage too.
It does though what it says in it?s title therefore i?m quiet satisfied with this product.
Quality of the material has a bit of a cheap expression.
Color coding or numbering would have been preferable for the cables.
Qualità
1
0
Segnala un abuso

Segnala un abuso