Tovább az oldal tartalmához

Table Microphone Boom Arm

  • Aluminium construction
  • Locking centre joint
  • 5/8" threaded connector
  • Table clamp for up to max. 56 mm table thickness
  • Pre-wired with XLR cable
  • Length of upper arm: 43 cm
  • Length of lower arm: 40 cm
  • Maximum load capacity: 1.5 kg
  • Colour: Black
  • katalógusunkba bekerült: Szeptember 2018
  • Termékszám 437359
  • mennyiségi egység 1 darab
  • Type Microphone Boom
  • Colour Black
27 990 ft
Minden ár ÁFÁ-val
Azonnal szállítható
1

158 Ügyfelek értékelései

4.2 / 5

stabilitás

kivitelezés

103 Vélemények

S
Stationvoice 19.03.2021
Nagy hátrány, hogy a lényeges kopó elemek, amik az asztallaphoz rögzítik, műanyagból vannak. A szorító tekerő feje igen kicsi, így nem lehet kellő nyomatékot kifejteni vele, állandóan elmozdul, mert a csuklók viszont komolyabb erőt fejtenek ki. Nem szerencsés konstrukció, a műanyag helyett fém alkatrészekre lenne szükség.
kivitelezés
stabilitás
0
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
P
not bad but room for improvement
PKristoffersson 13.02.2020
I bought this table microphone stand so I could do work either sitting or standing by my desk, depending on whether I would be singing or speaking.

This stand supports my microphone (a t-bone 400) with no issue and the reach is long. However, adjusting it is a bit of a pain. There are three separate joints that need to be tightened. The joint closest to the microphone is rather limited in its range of motion. Also, since all joints are hinge type joints it's not easy adjusting to get the microphone exactly where you want it. Overall it's something one can work around, it just takes time.
2
1
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
S
Disgusting Design Flaw – Avoid at All Costs
SmarttMark 22.06.2025
I deeply regret purchasing the Millenium DS200 Black mic arm. On the surface, it looks sturdy enough, but the design is absolutely appalling. If the wire goes—which it will, eventually—there is no accessible way to replace it unless you literally cut the wire with scissors and attempt to re-thread it. Why? Because the plug won’t fit through the internal path. This makes it essentially disposable once a fault occurs.

We’re not talking about a budget set of earbuds here. This is sold as a professional boom arm, yet it’s built like a cheap toy. A product that forces you to destroy and replace it within a few years if anything goes wrong is unacceptable. It’s the definition of bad engineering and poor sustainability.

If I could rate it zero stars for quality and stability, I would. Absolutely disgusted. Never again.
kivitelezés
stabilitás
0
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
S
had this for about 1 year
SixStackJack 06.01.2022
bought this one coas i needed a somewhat cheap boom arm for my AT2020 mic, and it works great, the arm keeps still and its somewhat easy to adjust it to your needs,
i had some problems getting the part where you fasten it to the table to stay in place, so i ended up drilling two holes from the top of the "plate" into the table, and then screw it in :D. now it wont move eaven if there was an earthquake :;D
kivitelezés
stabilitás
0
0
Jelentem!

Jelentem!