SM
Ein Muss
Zu den Chimes ist es ein Muss, diesen Halter dazuzubestellen. Damit lassen sich die Chimes gut auf Notenständern zum Beispiel befestigen.
0
0
Bewertung melden
FN
a little wobbly and long
Unless you really tighten the screws, this design hangs a little bit and will allow movement if you pull upward. This means it's not perfect for lightweight aluminum stands as it will bend the stand where the chimes holder clamps. On narrow stands, it will not tighten all the way.
Rather than the gate-like latch, a two-diameter slot that some of the other clamp manufacturers use would be ideal here, as this would improve stability on tilted stands. This would be more difficult to machine and would raise the cost, so the current design is understandable although a bit frustrating.
Regarding the length: If you mount this on a straight cymbal stand, the cymbal will be a lot farther to reach than the chimes (inconvenient for a kit drummer, especially for a splash cymbal or small crash). If you mount this on a boom cymbal stand, you have the weight of a cymbal plus the weight of chimes being supported primarily by one of three legs. It's better with a sandbag, but then you're carrying around a sandbag to gigs.
Ideally, the bend would be right near the chime mounting tab (just 1 or 2 cm away) and then the rest of the bracket could have three or four holes, so the holder can be "short", "medium", or "long" lengths from the stand. This wouldn't be difficult to change on their existing design (add a few extra bends and drill holes) and would then allow a drummer to put their chimes exactly in the right spot for their preferences and other equipment.
Rather than the gate-like latch, a two-diameter slot that some of the other clamp manufacturers use would be ideal here, as this would improve stability on tilted stands. This would be more difficult to machine and would raise the cost, so the current design is understandable although a bit frustrating.
Regarding the length: If you mount this on a straight cymbal stand, the cymbal will be a lot farther to reach than the chimes (inconvenient for a kit drummer, especially for a splash cymbal or small crash). If you mount this on a boom cymbal stand, you have the weight of a cymbal plus the weight of chimes being supported primarily by one of three legs. It's better with a sandbag, but then you're carrying around a sandbag to gigs.
Ideally, the bend would be right near the chime mounting tab (just 1 or 2 cm away) and then the rest of the bracket could have three or four holes, so the holder can be "short", "medium", or "long" lengths from the stand. This wouldn't be difficult to change on their existing design (add a few extra bends and drill holes) and would then allow a drummer to put their chimes exactly in the right spot for their preferences and other equipment.
0
0
Bewertung melden
L
Hält was aus!
Habe mir den Chimes Holder für die Befestigung der LP Vereínschimes beschaft. Top Qualität und Verarbeitung und vor allem "hält" er, was er verspricht. Auch wenn die ganze Geschichte mal umgestoßen wird. Der bleibt dran.
Die Handhabung ist proffesionel gelöst.
Top Empfehlung.
Die Handhabung ist proffesionel gelöst.
Top Empfehlung.
0
0
Bewertung melden
D
Funktioniert prächtig, Qualität in Ordnung
Der LP 26D Chimes Holder gibt einem die Möglichkeit in ca. 20 cm Abstand zur Achse eines Beckenständers o.ä. die Chimes in günstiger Reichweite nahezu beliebig zu positionieren. Dabei wird der Balken, von dem die Klangstäbe abgehängt sind, in frei einstellbarer Neigung stabil per Flügelschraube angeschraubt, sodass die unteren Enden der Klangstäbe z.B. auf gleicher Höhe liegen und mit ausreichend Abstand zum Ständer frei hängen. Damit sind sie perfekt bedienbar, sowohl mit der Hand, als auch aus der Ferne mit einem Drumstick. Die Verarbeitungsqualität lässt keine Wünsche offen.
0
0
Bewertung melden
Sa
Robust und Einfach
Seit Jahren im Einsatz ohne Probleme. Die Gewinde sind leichtgängig. Die Backen bieten optimalen Halt. Die Verchromung ist einwandfrei ausgeführt. Mir persönlich fehlt eine Gummidämpfung an der Aufnahme zum Ständer hin.
TIP: Da die Chimes schnell zum "klingeln" neigen empfiehlt sich eine Montage an einem separaten Ständer ohne Kontakt zum Set.
TIP: Da die Chimes schnell zum "klingeln" neigen empfiehlt sich eine Montage an einem separaten Ständer ohne Kontakt zum Set.
1
0
Bewertung melden
C
Wird nicht fest
Dieser Halter ist aufgrund der glatten Bauweise im Bereich der Doppelschrauben nicht an einem Ständer fest zu arretieren. Der Riegel schiebt sich beim Festziehen der äußeren Schraube in Laufrichtung mit nach oben, das geht kaum zu unterbinden. Gut gedacht, schlecht gemacht.
0
0
Bewertung melden
b
Must have zur Chimes.
Ist für mich ein Must have zur Chiemes.
Etwas habe ich noch nachgearbeitet und würde ich allen empfehlen. Vor der Mutter noch eine große,breite Unterlegscheibe , wo passend ein Gummi aufgeklebt ist mit Gummi zum Chimes einsetzen.
Dann hat man auch das Proplem mit dem "Gleichgewicht" und evt. Rutschen nicht.
Etwas habe ich noch nachgearbeitet und würde ich allen empfehlen. Vor der Mutter noch eine große,breite Unterlegscheibe , wo passend ein Gummi aufgeklebt ist mit Gummi zum Chimes einsetzen.
Dann hat man auch das Proplem mit dem "Gleichgewicht" und evt. Rutschen nicht.
0
0
Bewertung melden
HH
Perfekter Halter
Dieser Halter efüllt seine Aufgabe perfekt. Da wackelt nichts, die Schrauben ziehen gut. Das einzig Wünschenswerte wären Gummibeläge an den Stativklemmen, um so Vibrationen vom Stativ nicht so sehr zu übertragen (was sich aber in Grenzen hält).
0
0
Bewertung melden
AR
Nicht billig, aber sehr sehr gut
Benutze die Halterung nun ca. 2 Monate. Bin sehr zufrieden.
Sehr guter Halt. Flexibel an vielerlei Stativen einsetzbar.
Preislich nicht ganz billig. Aber es lohnt sich. Behaupte mal,
die Halterung hält (m)ein Leben lang.
Sehr guter Halt. Flexibel an vielerlei Stativen einsetzbar.
Preislich nicht ganz billig. Aber es lohnt sich. Behaupte mal,
die Halterung hält (m)ein Leben lang.
0
0
Bewertung melden
M
Gut!
Gewohnte gute LP Qualität! Mehr ist dazu nicht zu sagen!
0
0
Bewertung melden