Sfortunatamente si è verificato un errore, La preghiamo di riprovare più tardi.
t
Precise and stable
The machine heads are extremely solid and allow precise tuning and stability.
Esthetically flawless and elegant as any black hardware, the installation is easy, IF you have corresponding holes, otherwise you might have some difficulties, as I had, because the mounting rings are slightly smaller than the most common ones.
The machine heads are similar to the newest ones used on Fender basses, although they don't have the typical trapezoidal plate but a smaller one.
Esthetically flawless and elegant as any black hardware, the installation is easy, IF you have corresponding holes, otherwise you might have some difficulties, as I had, because the mounting rings are slightly smaller than the most common ones.
The machine heads are similar to the newest ones used on Fender basses, although they don't have the typical trapezoidal plate but a smaller one.
1
0
Segnala un abuso
Sfortunatamente si è verificato un errore, La preghiamo di riprovare più tardi.
r
great quality
used for experimental long string instrument, to put tension on +2m piano wire. did the job just fine. had to (over)tighten the screw because of higher tension than usual (and unorthodox break angle), which put too much tension on the plastic washer inside, but once installed properly they held out without further complaints. that said, if you're using them for what they were are for, instead of the abuse i put them through, i'm sure they will also satisfy :)
0
0
Segnala un abuso
Sfortunatamente si è verificato un errore, La preghiamo di riprovare più tardi.
P
All good
I used these to replace the revoltingly bad tuners on my Sterling Ray 35, and they are pretty much flawless so far. For info, I had to drill new holes on the bass head but that's unavoidable, at least for black tuners.
I haven't seen any issue with these, they seem solid, keep the tune perfectly and are easy to adjust. Simple and flawless as a good hammer.
I haven't seen any issue with these, they seem solid, keep the tune perfectly and are easy to adjust. Simple and flawless as a good hammer.
0
0
Segnala un abuso
Sfortunatamente si è verificato un errore, La preghiamo di riprovare più tardi.
up
Schaller nuff said.
Got these on my Ray 24 as well in chrome. Got these for the PB-20 bass.
They're black chrome. Feels like powder coat way more durable then any paint.
Never had issues with schaller products and I have been using them since the 80's.
Everything is there, screws, rims the lot. I put a dab of grease on the worm for extra smoothness.
Excellent replacement for any type of P/J bass or stingray.
You can reverse these so for a Ray look no further.
They're black chrome. Feels like powder coat way more durable then any paint.
Never had issues with schaller products and I have been using them since the 80's.
Everything is there, screws, rims the lot. I put a dab of grease on the worm for extra smoothness.
Excellent replacement for any type of P/J bass or stingray.
You can reverse these so for a Ray look no further.
0
0
Segnala un abuso
Sfortunatamente si è verificato un errore, La preghiamo di riprovare più tardi.
A
High quality tuners for Jazz bass
I looked around for a while for a good quality set of tuners for the Fender Jazz bass I am building. I wanted the best quality for my budget and found these. The quality is superb, much better that the standard Fender offerings and as I specifically wanted black chrome (not a painted version), I am very satisfied. The fact that they are made in Germany and not made in a Chinese factory with a brand name stuck on, is very reassuring.
0
0
Segnala un abuso
Sfortunatamente si è verificato un errore, La preghiamo di riprovare più tardi.
g
steady choice
fitted in a custom p-bass reverse neck the view is great. its fits almost the majority of necks out there and they are very steady and hard so bass doesnt detune often
0
0
Segnala un abuso
Sfortunatamente si è verificato un errore, La preghiamo di riprovare più tardi.
C
Nice Upgrade
I bought the Machineheads for my Stingray.
They fit perfectly. I didn´t had to drill new holes. The factory holes were exactly on the same position.
The quality is very good, the black paint seems to stay FOREVER
They stay in tune for a long time.
They fit perfectly. I didn´t had to drill new holes. The factory holes were exactly on the same position.
The quality is very good, the black paint seems to stay FOREVER
They stay in tune for a long time.
0
0
Segnala un abuso
Sfortunatamente si è verificato un errore, La preghiamo di riprovare più tardi.
MJ
Great tuners
Easy fitting, great look, great tuners.
0
0
Segnala un abuso
Sfortunatamente si è verificato un errore, La preghiamo di riprovare più tardi.
I
great tuners
fitted perfectly on my bass , had no problem with them whatsoever , they look amazing and they seem durable.
0
0
Segnala un abuso
Sfortunatamente si è verificato un errore, La preghiamo di riprovare più tardi.
T
Schaller Quality
Have used various pieces of Schaller hardware over the years and the design & quality is always amazing. These machine heads are no exception, great look & design and hold tune perfectly.
0
0
Segnala un abuso
