Kundcenter-inloggning
Land och språk Country and Language

Thomann FetAmp

95

Microphone Preamplifier

  • Extremely low-noise Class A JFet amplifier
  • For dynamic and ribbon microphones
  • 2 Matched JFet transistor pairs
  • Input: Balanced 3-pin XLR female
  • Output: Balanced 3-pol. XLR male
  • Input impedance: 20 kOhm
  • Gain: 28 dB (@ 3 kOhm source impedance)
  • Frequency response: 10 - 50,000 Hz (+/- 1 dB)
  • Requires phantom power: 24 - 48 V.
  • Dimensions (L x W): 77 x 22 mm
  • Weight: 35 g
  • Developed and produced in Germany

Note:

Does not allow phantom power to pass through to the microphone

Channels 1
Number of microphone inputs 1
Instrument input No
Tubes No
Compressor/Limiter No
Equalizer No
De-Esser No
Phantom power No
Phase Reverse No
External effect loops No
Analogue Outputs XLR
Digitale Outputs 0
Headphone connection No
Level Meter No
Artikelnummer 495774
B-Stock från 569 kr tillgänglig
619 kr
inklusive moms, 99 kr frakt tillkommer
Tillgänglig
Tillgänglig

Denna artikel finns i lager och kan skickas ut omgående.

Information om leveransen
Leverans beräknas mellan Måndag, 25.10. och Tisdag, 26.10.
1
3 Säljranking

95 Kundrecensioner

5 71 Kunder
4 14 Kunder
3 8 Kunder
2 1 Kund
1 1 Kund
4.6 / 5

drift

funktioner

ljud

hantverkskvalitet

S
Noiseless gain for dynamic / ribbon mics, plus protection
Skaven252 30.12.2020
Normally dynamic and ribbon mics should not get any Phantom power because they may get damaged. Instead you need to boost their gain on the mixer quite a bit, and with some lower quality internal preamps this may raise the noise level as well.

The FetAmp solves this by sitting between the mic and the mixer/amp, taking the Phantom power and using it to cleanly amplify the mic signal. It also blocks the Phantom power from going into the mic so it protects the mic from accidental power.

Simple, useful, works straight out of the box and hardly needs instructions. The Thomann FetAmp is an equivalent product to the TritonAudio FetHead, but at a lower price. It is slightly longer than the FetHead if size matters.

Pros:
* Clean amplification
* Protects dynamic / ribbon mics from accidental power

Cons:
* An additional dongle that you need to place somewhere along the cabling, or directly on the mic. You'll need to find a place for it.
drift
funktioner
ljud
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

R&
Perfect preamp for ribbon and other mikes
Rasmús "Michelle" Pasmús 19.06.2021
This is a great example of good stuff for a low price. I'm thankful Thomann exists!
drift
funktioner
ljud
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
B
Why pay more they work great. Do a very clean job at amplifying my Ribbon microphone signals.
Banditman 12.10.2021
Two of these came with the two t.bone RB 500 kits from Thomann. Tested and amazed at the low noise level. Worth every penny. Packed very well indeed. Fast delivery. What amazes me I buy gear from Thomann, comes all the way over to Northeast of England at great prices. Yet never had a damaged box yet. Thank you Ladies and gentlemen Of Thomann. Once again a very happy customer.
drift
funktioner
ljud
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
Ag
Simple and elegant solution to adding gain
Audio geek 09.05.2021
These FetAmps were bundled with the new SM7B microphones we purchased for a studio rebuild. They do exactly what they say on the tin and give the 7B a much needed boost. For some reason though when used with our Alice Series A desk we get a very low level buzz induced to the signal chain and this affects all three FetAmps and channels in any combination. If I try them all on another mixer (D&R Airmate) the buzz disappears altogether and the gain improvement is crystal clear so I can only attribute the issue to the Alice desk itself. Luckily the Alice has a good 60dB of adjustable gain and these channel are superbly quiet so we weren't in trouble. I still need to experiment further with another Alice Series A in the second studio and probably just need to add some decoupling to the channel strip to soft this buzzing issue. After all they are classic mixers and need a bit of TLC from time to time!
drift
funktioner
ljud
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

Fråga oss