Thomann FetAmp

108

Microphone Preamplifier

  • Extremely low-noise Class A JFet amplifier
  • For dynamic and ribbon microphones
  • 2 Matched JFet transistor pairs
  • Input: Balanced 3-pin XLR female
  • Output: Balanced 3-pol. XLR male
  • Input impedance: 20 kOhm
  • Gain: 28 dB (@ 3 kOhm source impedance)
  • Frequency response: 10 - 50,000 Hz (+/- 1 dB)
  • Requires phantom power: 24 - 48 V.
  • Dimensions (L x W): 77 x 22 mm
  • Weight: 35 g
  • Developed and produced in Germany

Note: Does not allow phantom power to pass through to the microphone

Channels 1
Number of microphone inputs 1
Instrument input No
Tubes No
Compressor/Limiter No
Equalizer No
De-Esser No
Phantom power No
Phase Reverse No
External effect loops No
Analogue Outputs XLR
Digitale Outputs 0
Headphone connection No
Level Meter No
Tillgänglig sedan Augusti 2020
Artikelnummer 495774
Design Adaptor
625 kr
inklusive moms, 99 kr frakt tillkommer
Tillgänglig
Tillgänglig

Denna artikel finns i lager och kan skickas ut omgående.

Information om leveransen
Leverans beräknas mellan Fredag, 10.12. och Måndag, 13.12.
1
4 Säljranking

76 Kundrecensioner

S
Noiseless gain for dynamic / ribbon mics, plus protection
Skaven252 30.12.2020
Normally dynamic and ribbon mics should not get any Phantom power because they may get damaged. Instead you need to boost their gain on the mixer quite a bit, and with some lower quality internal preamps this may raise the noise level as well.

The FetAmp solves this by sitting between the mic and the mixer/amp, taking the Phantom power and using it to cleanly amplify the mic signal. It also blocks the Phantom power from going into the mic so it protects the mic from accidental power.

Simple, useful, works straight out of the box and hardly needs instructions. The Thomann FetAmp is an equivalent product to the TritonAudio FetHead, but at a lower price. It is slightly longer than the FetHead if size matters.

Pros:
* Clean amplification
* Protects dynamic / ribbon mics from accidental power

Cons:
* An additional dongle that you need to place somewhere along the cabling, or directly on the mic. You'll need to find a place for it.
drift
funktioner
ljud
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

R&
Perfect preamp for ribbon and other mikes
Rasmús "Michelle" Pasmús 19.06.2021
This is a great example of good stuff for a low price. I'm thankful Thomann exists!
drift
funktioner
ljud
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
W
Cheap Fet preamp on ribbon mic
WazaHimself 28.11.2021
I mainly bought this to have the 20 db boost on my RM700 ribbon mic and to avoid passing the 48v if mistakenly left/turned on the channel.

It does the job without adding too much noise and colouring the signal!
drift
funktioner
ljud
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
R
Does the job perfectly, needs more recognition
Ronfontu 25.01.2021
Little disclaimer: I would have gone for the Klark Teknik CT1 if it were in stock but I needed an preamp asap.

This preamp does a good job and needs more recognition imo.
There is not much to say, go for it if you want to save money and avoid overpriced stuff. I used this with the Rode Podmic (I have 2 of each) and it let me put my gain way lower, reducing ambient noise. On the two FetAmps I have bought, one is a little bit loose when plugging it into the mic, that's why I gave it 4 stars. Other than that, I didn't have any problem. I would recommend this item.
drift
funktioner
ljud
hantverkskvalitet
4
0
Anmäl recension

Anmäl recension

Fråga oss