Millenium BS-2010

206

Speaker Stand

  • For speakers up to 30 kg
  • Material: steel
  • For flange diameter of 25 mm
  • Foot diameter: 1000 mm
  • Extendable from 119 - 200 cm
  • Weight: 2.6 kg
  • Colour: Black
  • Incl. 25 mm diameter adapter for M6 thread (12 mm long)
Tillgänglig sedan September 2013
Artikelnummer 320824
försäljningsenhet 1 Styck
Pole diameter 25 mm
2 pieces Set No
Material Steel
Crank No
Ringlock No
Pneumatic No
Feet Tripod
Colour Black
Min. Height 1190 mm
Max Height 2000 mm
Weight per Stand 2,6 kg
Max. Load 30 kg
Visa mer
245 kr
inklusive moms, 99 kr frakt tillkommer
Mängdrabatt
Pris per styck Du sparar Summa
245 kr 1
229 kr 6,5% 2
i lager
i lager

Produkten finns i lager och kan levereras omgående.

Information om leveransen
Beräknat utskeppningsdatum till Torsdag, 25.04.
1

206 Kundbetyg

4.4 / 5

Du måste vara inloggad för att kunna betygsätta en produkt.

Obs! För att undvika att betygsättningen är byggt på rykten eller smygreklam kan bara kunder som har köpt produkten från oss sätta sitt betyg.

Efter inloggningen i kundcentret kan du se vilka produkter som kan betygsättas.

funktion

stabilitet

hantverkskvalitet

84 Recensioner

S
Funkar fint där de står
Simon3697 06.01.2019
Detta är inte det slitstarkaste man hittar på marknaden, men de är billiga och om de ska så i en replokal så funkar de finfint.
funktion
stabilitet
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
M
Simple stand serving superbly
Michal3806 10.07.2015
as far as stands go, this one will serve you well if you don't put too heavy speakers on top - it's rated to up to 30 kilograms - and is better suited for smaller PA sets.

I purchased this for my Roland Cube CM30 which weighs about 5.5 kilos and is rather small and it feels like a perfect match, not too big, not too small, not too heavy.

Just a word of advice - the 25 mm tube and M6 thread means that for anything else you'll need adapters. I spent a while to get an adapter to the Roland's 3/8 thread but it was my fault, not the stand's. So, to avoid surprises, make sure to check thread compatibility.

But again, if there's a match, this will do the job for a great price.
funktion
stabilitet
hantverkskvalitet
2
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
Lm
Speaker stand
Luke malta 21.03.2022
Very stable stand and high quality but the top plastic caps are loose and will stuck to speaker when when speaker removed from stand.
funktion
stabilitet
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
A
Good value stand for a small speaker
Anonym 14.11.2014
I'm using this for a Behringer B205D active monitor that we use as a small PA. The 205D is designer for a mic stand but it felt a bit insecure. This is much more stable and goes a lot higher.

The B205D mounting spigot holds it on a 5/8" mic adaptor leaning back at an angle but I found a microphone table clamp on Amazon which was a short piece of steel channel with a 6mm threaded hole on one flange (for the clamp screw, ideal for the threaded stud on top of the speaker stand cap thingy) and a 3/8" mic adaptor screw on the top. I put it in a vice and bashed the top flange into the right angle to hold the speaker upright, added a 5/8" adaptor and the mounting spigot and it all works well.

So while this is not as light or compact as a mic stand, for most gigs its just right, goes above head height if you need to, and stable enough. If your speaker will fit the 25mm tube, or the 6mm threaded top cap it's fine.
funktion
stabilitet
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension