EV N/D Microphone Handle

65

Handle

  • For microphones from the EV N/D series
  • EV No. 480739
Tillgänglig sedan Oktober 2001
Artikelnummer 146710
försäljningsenhet 1 Styck
343 kr
inklusive moms, 99 kr frakt tillkommer
i lager
i lager

Produkten finns i lager och kan levereras omgående.

Information om leveransen
Leverans beräknas mellan Torsdag, 4.04. och Fredag, 5.04.
1

65 Kundbetyg

4.9 / 5

Du måste vara inloggad för att kunna betygsätta en produkt.

Obs! För att undvika att betygsättningen är byggt på rykten eller smygreklam kan bara kunder som har köpt produkten från oss sätta sitt betyg.

Efter inloggningen i kundcentret kan du se vilka produkter som kan betygsättas.

hantverkskvalitet

40 Recensioner

EH
EV N/D Microphone Handle
Eric H 26.03.2018
EV:s mikrofoner är trevliga och jag använder ett par olika sådana. Efter ett antal år blir gummit i handtagen lite torrare och kan spricka. Väldigt bra att det finns reservdelar att tillgå till vettigt pris.
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
So
Great part.
Sound of the Suburbs 21.05.2020
Repaired my old EV n/d mic, it is like brand new again. It’s hard to fit and some lubricant and a little heat be required to push it on. Do not use Vaseline or any oil based lubricant as it might react with the handle material. Use a water based lubricant like KY Jelly or Durex (sorry not meaning to be rude, but these are the most easily available water based lubricants). Water based lubricant dries quickly too and the sleeve will stay tight on the mic. Apply lubricant to the metal body of the mic and slide it on. Warning - Be very careful- Don’t crush or damage the mic head by pushing hard. If you get stuck and cant push it on any further, get a hair dryer and gently warm the sleeve to soften it. Do not make it too hot or you will damage or melt it. Just apply enough heat to get it moving. Note - Pay close attention to the orientation of the XLR latch and look at the key slot location on the bottom of the new sleeve to make sure it lines up BEFORE you slide the sleeve onto the mic. If you get it wrong, just warm the sleeve with the hair drier and rotate gently until the alignment is correct. If you do not align it with the latch on the mic cable XLR, the latch will lift the sleeve each time you connect the cable and eventually cause damage to it. Not sure why the original sleeve perished...either it chemically reacted with the foam in the carrying box as it was stored in there for years, or it was fitted originally using a lubricant which reacted with the sleeve, but i suspect the foam as it degraded caused it to break up. Who knows, but anyway my mic is useable again and looks brand new and I’m not storing it in the original case ever again. I’m happy as I have been trying for many years now to find and buy this part and get this amazing mic back into service again.
hantverkskvalitet
2
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
EG
If your EV mic's handle..
El Grado 06.06.2013
has been broken by someone from the audience trying to singalong to the DJ and then ramming it back into the clip, here is your perfect replacement. My EV is over 20 years old, so the handle was probably perished, so I'm grateful that this cheap item is available.
2
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
WP
Excellent replacement for an old EV microphone
W Pal 29.04.2018
I had purchased a used N/D767 with a fairly worn grip and this was a perfect replacement. Fits snugly, very comfortable to use and more grippy in the hand compared to Shure sm58s etc. All considered I found it to be good value
hantverkskvalitet
1
0
Anmäl recension

Anmäl recension