Adam Hall 5635 Humfrees M6

309

Rack Insulation Against Ground Loops

When rack mounting, additional conducting ground connections are created between 19" devices via the metal rails - the most frequent cause of hum noise.

Humfrees interrupts these ground loops. Devices are attached to the rack rails while electrically separated from each other. Additional plus: The front panels of the devices are protected against assembly damage.

  • 4 M6 screws
  • 4 Insulators
  • 4 Spacers
Tillgänglig sedan November 1999
Artikelnummer 128225
försäljningsenhet 1 Styck
Type Set
Thread Size M6
Length 16
Amount 4
Note Rack Isolation
Visa mer
41 kr
inklusive moms, 99 kr frakt tillkommer
Mängdrabatt
Pris per styck Du sparar Summa
41 kr 1
39 kr 4,9% 4
i lager
i lager

Produkten finns i lager och kan levereras omgående.

Information om leveransen
Beräknat utskeppningsdatum till Torsdag, 25.04.
1

309 Kundbetyg

4.1 / 5

Du måste vara inloggad för att kunna betygsätta en produkt.

Obs! För att undvika att betygsättningen är byggt på rykten eller smygreklam kan bara kunder som har köpt produkten från oss sätta sitt betyg.

Efter inloggningen i kundcentret kan du se vilka produkter som kan betygsättas.

hantverkskvalitet

137 Recensioner

C
Not that great
CLMusic 10.05.2021
The little plastic tabs that goes around the screws tears into pieces when you tighten the screws.
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

TS
Nice
Thin Simmons 16.03.2023
Do not know if they do anything special but we thought what the heck, might as well.
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
C
bad product
ColmO 18.03.2014
its only true purpose is to prevent against rack rash, it does not isolate equipment from each other, rather it isolates the rack equipment from the rack rails, so if 1 unit is causing hum this will transfer along each unit as their faceplates arent isolated


the screws dont fit my adam hall rack or gator case, it comes with a soft adapter for smaller screws

you have to cut the pieces out of their molds which isnt too difficult, but takes some accuracy to get them looking smooth with no bits sticking out.

the rubber/plastic warps/goes out of shape and shift position before you have the screws tightened, its difficult to gauge when its tight enough, when it feels tight your left with a misshapen piece


I dont normally right reviews straight after using a product but was so let down by these that I felt the need to write a review. some old bicycle inner tube would work better, or 2 plastic washers per screw would achieve the same
hantverkskvalitet
1
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
S
Your rack deserves the best!
SpyX 14.06.2018
Your rack deserves the best.
If you are a pro you don't need my advice, you know what you'll do. But for the rest of us who build a rack I'll tell you that, this set is a must for your rack.
You have spend a lot of money to buy audio hardware devices, you want the best for your sound so the last thing you want is hum from ground loops created between 19" devices via the metal rails.
Here comes the "Adam Hall 5635 Humfrees M6".
Consists of (4) M6 screws, (4) Insulators and (4) Spacers this is a set for one device. In a very good quality it'll give insulation to your rack against ground loops and protection to the front panels of your devices against assembly damage. Also looks nice aesthetically.
Coming in a good price, don't even thinking to don't make this buying.
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension