EV N/D Microphone Handle

65

Handle

  • For microphones from the EV N/D series
  • EV No. 480739
Disponível desde Outubro 2001
número de artigo 146710
unidade de venda 1 peça(s)
€ 29
IVA incluído, € 20 de portes de envio adicionais
Em stock
Em stock

Este produto encontra-se em stock e pode ser enviado imediatamente.

Informações sobre o envio
Envio previsto até Quarta, 20.03.
1

65 Avaliações de clientes

4.9 / 5

Terá de iniciar sessão para classificar produtos.

Nota: De forma a prevenir que as classificações sejam baseadas em boatos, conhecimento limitado ou má publicidade nós apenas permitimos classificações provenientes de clientes no nosso website, que tenham adquirido o equipamento através de nós.

Após iniciar sessão poderá encontrar todos os produtos que poderá classificar em classificar produtos no centro de clientes.

acabamento

40 Críticas

google translate gb
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
So
Great part.
Sound of the Suburbs 21.05.2020
Repaired my old EV n/d mic, it is like brand new again. It’s hard to fit and some lubricant and a little heat be required to push it on. Do not use Vaseline or any oil based lubricant as it might react with the handle material. Use a water based lubricant like KY Jelly or Durex (sorry not meaning to be rude, but these are the most easily available water based lubricants). Water based lubricant dries quickly too and the sleeve will stay tight on the mic. Apply lubricant to the metal body of the mic and slide it on. Warning - Be very careful- Don’t crush or damage the mic head by pushing hard. If you get stuck and cant push it on any further, get a hair dryer and gently warm the sleeve to soften it. Do not make it too hot or you will damage or melt it. Just apply enough heat to get it moving. Note - Pay close attention to the orientation of the XLR latch and look at the key slot location on the bottom of the new sleeve to make sure it lines up BEFORE you slide the sleeve onto the mic. If you get it wrong, just warm the sleeve with the hair drier and rotate gently until the alignment is correct. If you do not align it with the latch on the mic cable XLR, the latch will lift the sleeve each time you connect the cable and eventually cause damage to it. Not sure why the original sleeve perished...either it chemically reacted with the foam in the carrying box as it was stored in there for years, or it was fitted originally using a lubricant which reacted with the sleeve, but i suspect the foam as it degraded caused it to break up. Who knows, but anyway my mic is useable again and looks brand new and I’m not storing it in the original case ever again. I’m happy as I have been trying for many years now to find and buy this part and get this amazing mic back into service again.
acabamento
2
0
Reportar a crítica

Reportar a crítica

google translate gb
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
EG
If your EV mic's handle..
El Grado 06.06.2013
has been broken by someone from the audience trying to singalong to the DJ and then ramming it back into the clip, here is your perfect replacement. My EV is over 20 years old, so the handle was probably perished, so I'm grateful that this cheap item is available.
2
0
Reportar a crítica

Reportar a crítica

google translate gb
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
WP
Excellent replacement for an old EV microphone
W Pal 29.04.2018
I had purchased a used N/D767 with a fairly worn grip and this was a perfect replacement. Fits snugly, very comfortable to use and more grippy in the hand compared to Shure sm58s etc. All considered I found it to be good value
acabamento
1
0
Reportar a crítica

Reportar a crítica

google translate gb
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
G
EV MiC handle
Gary6465 29.12.2016
Sinple bit of kit, fitted the EV MIc pefecty, so i can now use one my favourite Mics again , thankyou Thomann.
1
1
Reportar a crítica

Reportar a crítica