Millenium Rackstand 12U

87

Rack Stand

  • Size: 12 U
  • Free-standing open rack
  • Material: Steel
  • Threads for M5 screws
  • Base depth: Approx. 36 cm
  • Angle of inclination: 25° vertical
  • Total height: Approx. 55 cm
  • Colour: Black
  • Includes a set of screws
usable height in U 12 U
Material Steel
Wheels No
Produkt dostępny od Wrzesień 2018
Numer artykułu 442738
Type Tabletop Stand
Height min. 550 mm
Height max. 550 mm
Special Design No
Pokaż więcej
15,30 € 70,11 zł
Zawiera podatek VAT, nie zawiera kosztów wysyłki 9,90 €
Cena w zł podana jest w celach orientacyjnych
Artykuł dostępny w magazynie
Artykuł dostępny w magazynie

Artykuł jest dostępny od ręki.

Informacje dotyczące wysyłki
Wysyłka spodziewana do dnia Czwartek, 9.12.
1
61 Ranking sprzedaży
google translate gb
Wystąpił błąd. Proszę spróbować później.
JM
Ended up using rivets
Joe Montana 23.10.2019
Here is the story...
Bought this particular one over many types in other shops because it looked like the best one, good design, no sharp edges, rubber feet, so when it came I thought it would only take 10 minutes to assemble, and under an hour in total to equip the rack with mixer, etc.
I made the mistake of assembling this on a sofa, so it was wobbly on the table, I loosened everything and then tighten everything on the flat surface. Wobble fixed, 10 minutes.

This is where my troubles began...
I noticed that the whole thing was leaning to the left, so I tried bending it and re-tightening the bolts. It didn't help, so I figured that inserting the mixer and other units would straighten it out (which it did, in the end).

So I lay the rack down and placed the mixer in position, I slid it upwards to check out the spacing, and found out the top part was very narrow. I cycled to the local town for a bag of washers to space the rack top a bit wider. After putting them in, I saw that the top was still too narrow. It turned out that the top bar was too short by about an inch. I had to remove it completely by the end.
If I was in charge of the manufacturing, that product would not leave the factory until that issue is fixed.
But that's not the end of it...

Started putting in the screws and found that they only go in about halfway, not enough to secure the mixer.
It turns out that the black powder coating / paint that is on the rack is also in the bolt threads and on the bolts themselves, so they simply don't fit the holes anymore.
The bolt steel is not hard enough to "push" the paint out by turning the bolts, they just get mushed up instead. Using a chainsaw file to trim off some of the paint doesn't work either, you just trim off the threads aswel. I'm not going into town for a tap-and-die set to try re-thread the holes, I might as well make my own rack from scratch.

As it was getting later in the evening, I opened a drink and sat to think about how to proceed.
I could either send it back to Thomann (takes a week) and then shop around for a different one, or cycle to the village the next day for M4 nuts and bolts (I recommend), or I could use rivets.
I decided to use rivets as I was losing patience with this thing and wanted to be done with it.

So I revetted in the mixer, no problem, I had the rivets, washers, tool, etc.
Drum module is next, again it went more or less to plan, with some swearing.
Next came the Novation Peak. After putting on the rack ears I saw that the unit would not fit the rack. I calmly sat down and had another drink.
i finally decided to bend the top of the rack outwards, enough to drop in the synthesizer. This worked and with some more swearing and grunting I was soon finished. 2 hours altogether, instead of 1.

Conclusion
Eventually goes together the way you want it, but not without a lot of work on your part.
Because of the tilt angle, the first 2 unit slots from the bottom are only of use with units that are very shallow, like a power strip or socket patches. The top unit is also occupied by the useless steel bar.
This gap at the bottom gives you space to put other items on the desk, like a semi-modular synthesizer, Beatstep pro or effects pedals.

It says in the documentation that the rubber feet may stick to certain surfaces over time, so judging by the fiasco so far I can guess that they will corrode and weld themselves into the desk so well that it will take a hammer and chisel to get them off. I am counting the days. I may use beer mats under the feet

Overall - worth it if you can deal with the manufacturing shortcomings.
stabilność
wykończenie
7
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
s
For the price it's doable...
sdk75 20.10.2021
I bought this to rack up my Behringer Xenyx 2224 mixer and although the 4 holes on each side of the Behringer rack ears don't line up with the rack's holes, I could use the 2 upper holes on each side of the B' rack ears to fit in the mixer on top of the rack. It stands really firm on the table and in the end I'm quite happy with it. Beneath the mixer there is still room for a tabletop device. I've read in another review that the screws don't sink in nicely and that's true. It's rather impossible to bolt the screws in by hand. Instead I've used my Makita screwdriver and could force them into the holes. Total assembly time for me: 15 minutes. Having a mixer up in front of you is an enjoyable experience. Happy with this cheap solution!
stabilność
wykończenie
1
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
P
So bad i had to write about it
Peter_75 16.09.2021
I never write bad reviews, but this stand is just so bad that i must write something :-D
Ok, it's really cheap but for about 16€ they could at least cut a threads in holes, so if you buy one of this, i hope you have your thread making tool set ready!
Also spacing of mounting holes is way off. When mounting 8U Unit, the 4th hole is off by about 2 mm so there is no way to put a screw through.
If you want to use all 12U, you must remove upper bar which holds 2 parts together, but at least that does not compromise stability.
Beside that, there is not much to say... If you don't have time and/or tools to make your own threads in all holes, you should buy another stand of better quality
stabilność
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
m
Dont waste your money
mbolge 23.10.2019
I got these to use at home for some rack equipment I have. I haven't had and problems with millennium equipment before this and the price was good so I decided to go for two of them.
This is possibly the worst quality piece of equipment I have ever received, it is a total waste of money. Do not buy this unless you want to be disappointing. When I put the first one together I though maybe I just got a dud, but the second one was the exact same.
The screws supplied are near impossible to screw into the rack with no equipment in play, never mind trying it while holding some equipment in place. It's almost like the screw holes were tapped, and then the coating was applied afterwards, so now the screws don't fit it properly.
Save yourself the money and buy something better than this. They are totally unusable, mine are going in the bin, the cost to return them isn't worth the effort.
stabilność
wykończenie
6
0
Zgłoś nadużycie

Zgłoś nadużycie

Konsultacja