K&M 23325 Table Microphone Stand

328

Microphone Stand

  • Black
  • Cast-iron base with special rubber insert for silencing
  • Screwed, adjustable tube combination
  • Weight: 2.5kg
  • H: 217-347 mm
  • Base-Ø 180 mm
Produkt dostępny od Czerwiec 2013
Numer artykułu 316056
Jednostka sprzedaży 1 szt.
Type Desk stand
Colour Black
145 zł
Zawiera podatek VAT, nie zawiera kosztów wysyłki 49 zł
Dostępny w magazynie
Dostępny w magazynie

Produkt jest dostępny w magazynie.

Informacje dotyczące wysyłki
Wysyłka spodziewana do dnia Czwartek, 25.04.
1

328 Oceny klientów

4.8 / 5

Aby wystawić opinię, należy się zalogować.

Informacja: Aby opinie na temat sprzętu umieszczane na naszej stronie pochodziły jedynie od osób mających styczność z danym artykułem, umożliwiamy wystawianie ocen jedynie naszym klientom.

Opinie można wystawiać po zalogowaniu się w centrum klienta, używając opcji "wystaw opinię".

montaż

stabilność

wykończenie

188 Opinie

google translate gb
Wystąpił błąd. Proszę spróbować później.
DD
Feels heavier & sturdier than the photo!
Dr D 01.11.2019
I have a heavy RODE Procaster with shockmount plus TritonAudio Fethead and windshield attached, so I was concerned that a relatively short desktop stand with a not so big base circumference (180 cm or 6-inches) would suffice. Thankfully, I can report that this K&M mic stand is absolutely perfect. It is really quite heavy @ 2.5 Kg ( > 5 lbs) weight, thus can easily cope with more than a kilo of weight up top. In fact, when I grab the head of the mic whilst attached to this stand and try and pull it or tip it over, it just will not.
The other cool aspect of this particular mic stand, is the easily adjustable telescopic pole to adjust the height of the mic. Although it does not increase the overall height by that much, it is sufficient to get the mic up to head head whilst seated at a desk with this stand in front of you. It also secures very well and does not slip or move at all.
Finally, the circular rubber inlay on the rear side of the base, just feels quality - soft but does not allow the stand to slide at all. Even hitting the side of the base with my clenched fist does not move it.
I would highly recommend these K&M mic stands and the next time I shall be in the market for another one, I will look for this brand again.
montaż
stabilność
wykończenie
3
1
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
N
Doubles as a battel hammer
Nänad 04.01.2021
Seriously, this thing is so sturdy, you can kill a guy with it. Has a rubber layer on the bottom which prevents it from sliding on top of a desk. RODE NT 1 fits perfectly on top of it. Can be used for recording instruments, but for recording conversations as well...and killing people (in which case RODE NT1 should be replace with Shure SM58, due to it's enhanced rigidness)
montaż
stabilność
wykończenie
8
1
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
r
Its decent
rayzer... 03.04.2022
It has a really heavy base so you wont be knocking it over accidentally but i found it sounded a bit hollow when i first used it by my computer.
After sticking some carpet and rubber squares under it that became a non issue.
Other than that its sturdy and does its job.
montaż
stabilność
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
AD
Nothing not to like.
A Dutch Person 11.01.2021
Reassuringly heavy, thank god. You can extend it 15 cm (unlike the K&M 232BK) which is great. It has a sturdy rubber ring at the bottom to dampen vibrations. It feels rock solid and I will probably also use it for live music (with omni and cardiods) in small interior locations (on table, shelf or chair) when there is no room for mike stands. They won't fall over.
montaż
stabilność
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie