Mixer ModuleModule A-138 is a four-channel mixer that can be used for mixing control voltages as well as for mixing audio signals. A separate attenuator is available for each of the four inputs. In addition, the mixer has an attenuator at the output, so that this can also represent the end of the audio chain.
Version with logarithmic potentiometers; Particularly suitable for mixing audio signals.
Podobne produkty i akcesoria
1–2 z 15 ocenWszystkie oceny
Doepfer A-138-B Mixer
For me the A-138b is an essential piece of equipment because it enables me to sum the outputs of up to 4 sound sources (for instance VCO's or noise sources) before sending the combined output to my A-108 Low pass filter module.
With one input employed, and with the channel and master levels set to 10, the volume of the output is the same level as the input signal. in other words, this module will not increase the gain of an input, it will only attenuate it.
When using multiple inputs I find I have to reduce the levels of the individual channels quite a lot, otherwise the output from the mixer becomes to much for next module in the chain. So if I am using 3 inputs, I will use a maximum of about 33% of each channel's volume.
The mixer appears to operate very quietly. It does not introduce much 'hiss' into the sound. Some reviewers have found otherwise , so it may be that my ears are not as sensitive as theirs.
I have rated the A-138b as 5 stars except for features, which I have given a 4 for. The reason for this is that the Doepfer website indicates that with no input into channel 1, the channel 1 level will act as a +5 volt DC offset. In other words, the unit *can* increase the level beyond that of an input signal. However, my unit doesn't work like this. As delivered, all 4 inputs on my A-138b work in the same way. The manual says there is a jumper I need to re-position on the rear of the circuit board to achieve the +5 volt DD offset with input level 1. I think this option should have been made available as a toggle switch on the front panel. It would be useful on occasions when I am only using 3 inputs, but I do not want to have to remove the unit from its case and re-position a jumper each time to achieve this!
Overall, another useful and great value unit from Doepfer, in my opinion.
Does its job!
Mixer ModuleModule A-138 is a four-channel mixer that can be used for mixing control voltages as well as for mixing audio signals. A separate attenuator is available for each of the four inputs. In...
Standard VCO for Modular System A-100Module A-110-1 (VCO) is a voltage controlled oscillator. The A-110-1 produces frequencies in a range of about 8 octaves, of which four waveforms are available...
Wasp Filter Special edition, Black front, Yellow knobs
Passive Multi-Port Distributor 8x Interconnected jacks, Sockets are divided into 2x quadruple groups; but can also be modified to an eight-multiple (soldering bridge on the circuit board), Width:...
ADSR Envelope Generator The module A-140 is a envelope generator and since it delivers control voltages, belongs to the modulation-modules. As soon as the ADSR is triggered at gate-input, it...
Quad ADSRThe module contains 4 independent ADSR envelope generators. Each sub-module has the controls Attack, Decay, Sustain and Release. With the 3-stage range switch, the desired time range can be...
Module Dual linear/exponential, VCA
Doepfer A-199 Spring Reverb Module - electronically simulated by means of 3 spiral springs. Spring reverb systems have a very characteristic sound that is based on the (insufficient) mechanical...
Doepfer A-180-3 Dual Buffered Multiples, dual buffered 1-in-3 multiple to copying/buffering of control and audio signals, Width: 4 TE / 4HP / 20.0 mm
Doepfer A-111-2; High End VCO II / VCLFO; Width: 14 HP, Current: +70mA (+12V) / -50mA (-12V)
Doepfer A-100 LC1 Low Cost Case for Eurorack Modules; build-in Power Supply A-100SSB (+12V/380 mA, -12V/380mA); 48 TE Version of the A-100LC3; build-in Bus Board with 8 Module connectors; Housing...
External Input / Envelope FollowerModule A-119 is used to integrate external audio signals into the system A-100, and includes the components pre-amplifiers, envelope follower and a comparator. The...
Noise/Random Voltage Generator Module A-118 is a noise and random voltage generator. It produces the following signals: white noise, coloured noise, and random voltage. White and coloured noise can...
Filter 12 dB Multi-mode filter, in which the circuit of the SEM module is used, Width: 8HP 40.3 mm, Depth: 55 mm (measured from the rear of the front panel), Power requirements: +30 MA (+ 12V) /...
Doepfer A-131 VCA - voltage controlled amplifier (logarithmic).
Doepfer A-157 Trigger Sequencer Subsystem 1-2-3, contains: A-157-1 Trigger Matrix (8x16) + A-157-2 Output Module and A-157-3 Input Module, generate up to eight trigger signals controlled by a 8x16...
Wasp Filter Module A-124 is a special 12 dB multimode filter using the "strange" filter circuit of the "EDP Wasp" (an analog synthesizer with black/yellow case built end of the seventies,...
Analog and Trigger Sequencer for Modular System A-100 The following functions are available for the two analog rows (rotary knobs): 8 Rotary potentiometers, Scale (stepless knob) on the lower...
Basic VCO for the A-100 modular system Voltage controlled oscillator, 3-Position toggle switch, Linear FM input and soft-sync input, Tune control range can be set between approx. 1/2 octave and 4...
Doepfer A-156 - Dual Quantizer.
darmowa wysyłka od 199 €
Faktura w walucie euro
|Cena za||1 szt.|
|Produkt dostępny od||styczeń 2004|
|w tej kategorii||Ranga 21|
|na thomann.de||Ranga 6315|