Naar de inhoud van de pagina

TonePros AVT2M CH

32

Wraparound Bridge

  • Metrisch met Locking Studs
  • Materiaal: brass
  • Radius: 12''
  • String Spacing: 10,4 mm
  • Stud to Stud Spacing: 82 mm
  • Kleur: chrome
Leverbaar sinds December 2010
artikelnummer 257644
verkoopseenheid 1 stuk
Colour Chrome
Design Wraparound
Single Rider No
String Holder No
€ 126
Alle prijzen incl. btw
Direct leverbaar
Direct leverbaar

Dit product is op voorraad en kan direct verzonden worden.

Informatie over de verzending
Levering zonder verzendkosten tot ongeveer Dinsdag, 10.12.
1

32 Klantenbeoordelingen

4.6 / 5

U moet ingelogd zijn om producten te evalueren.

Note: Om te voorkomen dat evaluaties gebaseerd zijn op roddel, geruchten of heimelijke advertentie staan wij op onze website alleen evaluaties toe van daadwerkelijke gebruikers die het geevalueerde product bij ons gekocht hebben.

Na inloggen vindt u alle producten die u kunt evalueren ook onder “Product evalueren” in uw klantencentrum.

afwerking

23 Recensies

A
Sustain, sustain, sustain...
Anoniem 23.03.2016
Zeer eenvoudig te monteren en te intoneren (ik gebruik de AVT2M op mijn PRS SE Singlecut i.p.v. de standaard PRS wrap around).

Ik was aangenaam verrast door de toename van de sustain maar bovenal door de verbeterde klank! De scherpe randjes verdwenen, de totaalklank werd 'mellow'.

Kortom een 'mod' op mijn gitaar die zeer de moeite waard blijkt!
afwerking
0
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
IC
Very Good
Isaac Campos 05.03.2019
I bought this to improve the original bridge on my Junior.
The original was fine, but I like to mess around with tuning (usually low ones as well) and the wrap-around, even when it was the compensated version, couldn't handle it very well.
I installed this one, that allows me to play around with the saddles and adjust the intonation much easier and better.
I'm very happy with it.
As usual, nice quality from TonePros
afwerking
1
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
D
Great wraparound bridge though a bit on the expensive side
Deiecide1 31.10.2018
I bought this bridge as a replacement for the original one I had on my 20-year-old Warlock. Since the guitar was a US import it had metric threads, so I didn?t even have to replace the inserts, the screws fit the original ones I had in the guitar body ?like a glove?. The spacing between the screws was also spot on, so the bridge is sitting exactly where it should.
Unlike the original bridge the TonePros AVT2M CH has a lot more possibilities for adjustments: in addition to being able to move the saddles there are also small Allen (hex) screws on the back of the bridge, which means that you will most likely be able to find the ?sweet spot? for your specific guitar where it will be perfectly intonated.
Among other pros is of course high build quality, everything is fit with very tight tolerances, so there is no wobbliness in the saddles or screws, which eliminates the potential for rattling noises.
What I also find very cool in the bridge is that it locks with the top screws and stays in place when changing stings and nothing falls off even if you take off all of the strings at once.
Among the cons I would say apart from being rather on the pricy side the bridge is a bit fiddly to adjust. It comes with a special small wrench which is supposed to be used to lower and raise the bridge, but it?s very difficult to get underneath it with this wrench and leaves a lot of possibilities of slipping and scratching the guitar top underneath. I ended up bending the wrench to make it a bit easier to adjust the bridge height, and not I can no longer use its handle to tighten the top screws (which you are supposed to according to TonePros manual). Another awkward thing is you have to keep the top screws loose when adjusting the bridge height, and you can really tighten them down only after you loosen the strings. But once you do that the bridge goes a little lower, so you might have to come back and adjust it again.
Generally, what I do when adjusting the action is I loosen the strings and then count the turns and tighten the top screws and after that tune to pitch and check the action, I found this the easiest and most accurate way to adjust the action. Luckily as it?s a locking bridge you won?t have to do it often.
All in all, I would recommend this bridge as a perfect replacement for any wraparound bridge you might have on your guitar, but be careful and measure your stud spacing, string spacing and threads to choose the right bridge for your guitar.
afwerking
1
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
L
Be prepared to do a little work.
Leedelta 19.11.2018
Good weight and feel to the bridge. Which adds to sustain and tone.

Instructions are clear, but watching a video on Youtube is still needed to understand how to fit and adjust. Especially to understand the back screws.

Intonation setting is tricky due to screws being under the strings. Akward more than anything else.

I would advise having some nut files nearby as the saddles are not pre-grooved, so if you do a lot of bending the G,B and E strings will need to be correctly fitted as they will glide along the unslotted saddles. Make sure the files match the string gauges.
afwerking
2
0
Evaluatie melden

Evaluatie melden