K&M 24116

307

Bevestigingsplaat M20

Stalen flensplaat met binnendraad te gebruiken met tussenpalen met schroefdraadbout M20. Op boxen te schroeven.

  • Flens-ø 105 mm met 4 boringen ø 6,5 mm
  • Kleur: zwart
  • Gewicht: 0,24 kg
artikelnummer 104910
verkoopseenheid 1 stuk
Electronic Accessories No
Cabinet Accessories Yes
Stand a. Flying Stud Accessories Yes
€ 9,40
Incl. btw plus € 5,90 verzending
direct leverbaar
direct leverbaar

Dit product is op voorraad en kan direct verzonden worden.

Informatie over de verzending
Levering verwacht rond Maandag, 29.04.
1

307 Klantenbeoordelingen

4.9 / 5

U moet ingelogd zijn om producten te evalueren.

Note: Om te voorkomen dat evaluaties gebaseerd zijn op roddel, geruchten of heimelijke advertentie staan wij op onze website alleen evaluaties toe van daadwerkelijke gebruikers die het geevalueerde product bij ons gekocht hebben.

Na inloggen vindt u alle producten die u kunt evalueren ook onder “Product evalueren” in uw klantencentrum.

afwerking

100 Recensies

N
Very good.
Nuissl 11.11.2019
It looks very good, it fits very well.
Time will tell if it is strong enough, but I assume this will be.
0
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
A
Really good product
Anoniem 25.02.2016
I'm a Live Audio engineer and bought these to use with some M20 K&M distance poles. They do a better job than my previous Adam Hall M20 sockets and were a closer fit.

I fitted these to a pair of Alto Black 18 subs, however, they didn't line-up perfectly. I'm not sure if this is due to the Alto's not being a standard fitting or the sockets not being quite right for a universal fitting. They needed slightly bigger holes drilling into the sockets (1mm) in order for the bolts to line up with the threads on the subs. They also could have had a larger diameter in order to spread the load more as they were smaller than the recessed area on the subs.

However, like I say, I'm not sure whether this is a problem with these sockets or with the Alto subs and so it would be unfair to mark them down without knowing for sure.

I may eventually secure them further to the M10 rigging points on the subs for more stability. But all in all... Another good product from K&M!
0
1
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
PA
A pole mount for a subwoofer done properly!
Peter A. 333 19.03.2014
Bought this as an upgrade for a pair of singe 15 subs that had the usual 35mm pole socket in. The problem with the traditional 35mm mount is that it's either just too wobbly that the pole and top box sit at a angle, or they're so tight that they get jammed in.

This solves the problem. A sturdy diecasting into which you screw a proper 20mm threaded speaker pole. Perfectly strong and exactly upright.

Had to make sure that plate was very secure, by adding an additional 150mm square piece of plywood inside the sub cabinet.

Very well made and has a tough powder coast finish that has not marked with extensive use.
0
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
I
Great quality casting.
Ian2612 17.03.2018
I wanted to mount an m20 thread pole onto my deck stand shelf, the good quality and slim depth of these were perfect to fit into the 18mm thick bird.
0
0
Evaluatie melden

Evaluatie melden