Göldo E250P

133

Push/pull Pot

  • Met 250 kOhm
  • To Pull
  • 2-Way Switch
  • 6 Pins
Leverbaar sinds December 2006
artikelnummer 112185
verkoopseenheid 1 stuk
Design Push Pull
Resistance Value 250 kOhms
Tandem Poti No
Push/Push Push/Pull
Solderless No
shaft type grooved
€ 11,90
Incl. btw plus € 5,90 verzending
direct leverbaar
direct leverbaar

Dit product is op voorraad en kan direct verzonden worden.

Informatie over de verzending
Levering verwacht rond Vrijdag, 19.04.
1

133 Klantenbeoordelingen

4.1 / 5

U moet ingelogd zijn om producten te evalueren.

Note: Om te voorkomen dat evaluaties gebaseerd zijn op roddel, geruchten of heimelijke advertentie staan wij op onze website alleen evaluaties toe van daadwerkelijke gebruikers die het geevalueerde product bij ons gekocht hebben.

Na inloggen vindt u alle producten die u kunt evalueren ook onder “Product evalueren” in uw klantencentrum.

afwerking

50 Recensies

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
M
Great Pot, good connections, quality feel.
Milodon 14.09.2018
Very good pot. Used to MOD an old guitar humbucker to coil split.
Very easy to install and use, only CON is it is quite tall! you MAY have to remove some material inside the guitar to make this fit in place of a regular pot.

I had to remove 4mm of material from the body inside my Strat to get the scratchplate to fit level again. This is on a standard USA strat in the VOL position, so as you can see if you are less confident with tools/basic luthiery, maybe ask your local guitar shop to fit it in this case.

Overall though, great sturdy pot which will last for years, great solid feel, no interference on the pickups when it is pulled (unlike some) so would reccommend, just check dimensions first!
afwerking
0
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
t
teaberryou 30.06.2020
I really like 99% of Goldo products, but this time it's just a pass. Yes, it got the job done, but it feels a bit flimsy compared to the Allparts and Fender versions. After fitting, the axle has a little play in it, which makes the knob go ka-klunk after I release it. It's the first time I'm using it for my builds (because the Allparts version wasn't in stock), so maybe it's just this piece I have, and not all of them. It's not a deal breaker, but if given the choice I'd stick to Allparts for my builds.
afwerking
0
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
g
Works Great
gDaddy 14.11.2017
Bought to replace pot in a bass guitar. Works Great.
afwerking
0
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
j
nice functional pot!
jerrry 14.09.2018
I took this pot to enable transition between parallel/series connection on humbuckes. It works fine and it gives you a feature nice to have in a guitar, but I think the quality is a little bit cheapish...
afwerking
0
0
Evaluatie melden

Evaluatie melden