EMG 1 or 2 Pickups HZ Wiring Kit

14

Pickup Installatie Kit

  • Met alles wat je nodig hebt voor de installatie van 1 of 2 passieve EMG Solderless pickups
  • Bevat potmeters met gegroefde as (standaard lengte)
  • 2 Volume potmeters
  • 2 Tone potmeters
  • 1 Pickup buss
  • 1 Power buss
  • 1 12B uitgang met batterij clip
  • 1 uitgang kabel
  • 4 Interconnect kabel
  • 2 Pickup Cable
  • Alleen geschikt voor passieve pickups!
Leverbaar sinds Augustus 2016
artikelnummer 391886
verkoopseenheid 1 stuk
€ 45
Incl. btw plus € 5,90 verzending
direct leverbaar
direct leverbaar

Dit product is op voorraad en kan direct verzonden worden.

Informatie over de verzending
Levering ongeveer tussen Woensdag, 3.04. en Donderdag, 4.04.
1

14 Klantenbeoordelingen

4.9 / 5

U moet ingelogd zijn om producten te evalueren.

Note: Om te voorkomen dat evaluaties gebaseerd zijn op roddel, geruchten of heimelijke advertentie staan wij op onze website alleen evaluaties toe van daadwerkelijke gebruikers die het geevalueerde product bij ons gekocht hebben.

Na inloggen vindt u alle producten die u kunt evalueren ook onder “Product evalueren” in uw klantencentrum.

afwerking

10 Recensies

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
A
Used it with EMG 40HZ set
Anoniem 30.03.2017
I bought a set of EMG 40HZ for a bass and since I didn't wanted to bother with all of the soldering I decided to go with EMG's solderless install (40HZ didn't included any of the quick install components, unlike active EMG pickups).

The whole idea with a solderless install is really great. It took me less than 15 minutes to get everything working.
Default connectors are wired for serial humbucker connection. But with spare EMG connector cable and 2-pin connectors you can easily change the connection type (I got 2 spare cables with my pickups that was used for split-coil hum-cancelling connection type).

Wiring kit is also compatible with any other passive pickups. The only thing you need to get it working is connecting 2-pin connector to the pickup cable instead of soldering it.

The only downside of the Wiring Kit I got, was the wrong wiring on one of the pickup cables. It took me a while until I finally measured pickup resistance on the connection cable and understood that 2 wires on the connector were out of place and pickup was working in single coil mode as a result. Fortunately it wasn't too hard to switch a few wires and get a perfectly working humbucker in the end.

I think this was just an isolated error, but in case anyone got some volume problems - check cable wiring first.
afwerking
3
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
B
Brilliant for installing EMG PHZ set
Basspower50 14.01.2019
I purchased a set of EMG PHZ pickups, however I found the included cable a little bit short to reach from the base of the pickup to the volume/tone controls (weird!). Anyway, I bought this and it came with absolutely everything I needed to complete the installation. Very happy and I would recommend to anyone who encounters a similar issue.
afwerking
0
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
LO
Managed 2 guitars
Lord O 07.09.2022
Bought this to rewire 2 Ltd guitars I bought years ago that some gorillas had seemed to rewire themselves. One had the quick connect on the pickups themselves so used the included cables. Managed to put Dupont connectors on the others and it worked well. All the components in the kit were good quality and went together easily.
afwerking
0
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
P
Makes life so easy !
Paul.7 16.10.2022
These solderless connections are a gane changer ! Plug and go
afwerking
0
0
Evaluatie melden

Evaluatie melden