Schoeps Accessori Microfoni
28 risultati. Visualizza articoli 125.
I prezzi includono l'IVA locale Spedizione gratuita per acquisti di un importo superiore a € 298
Microphone Amplifier CMC for MK Series CapsulesThe microphone amplifiers CMC are not amplifiers in the classical sense. Their task is rather to adapt the signals of the high-impedance condensate capsule for the very low-impedance, balanced transmission through the microphone cable....
- Power supply for capsules of MK series
- Power supply by 12V - 48V phantom power
- With balanced, especially low-impedance output
Hollow Foam Popscreen B 5 D For use especially on pressure-gradient transducers in light wind and as a close-speech guard. The B 5 D offers good effectiveness, yet has only a slight influence on the sound. It is made...
- Dimensions: 70 × Ø 50 mm (max)
- Colour: Grey
- Additional gray flocking
Schoeps CMC 6 UG xt - mic amp for MK-series capsules with 48V phantom power unit. Special version (frequency response up to 40kHz).
Windscreen Made of nylon fabric for the CMC series, Two separable halves, Wind noise attenuation at 18 km/h with omni-directional microphones 29 dB-A, Wind noise attenuation at 18 km/h with super-cardioid capsule 38 dB-A, Diameter: 80 mm, Colour: Light...
- Made of nylon fabric for the CMC series
- Two separable halves
- Wind noise attenuation at 18 km/h with omni-directional microphones 29 dB-A
Active Extension Tube
Active Extension Tube Length: 1200 mm, Colour: Anthracite, Tube swivel RG 8 included
- Length: 1200 mm
- Colour: Anthracite
- Tube swivel RG 8 included
Stand ClipThis tripod clip with joint has a foot with a 5/8 "-27 NS internal thread. Thanks to the supplied adapter, it can be screwed onto any type of tripod with 3/8" or 1/2" etc. The inclination of the microphone...
- With joint
- For microphones with a diameter of 20 mm
Elastic suspension holder For MS stereo method, For 20 mm microphones (CMC with capsule)
- For MS stereo method
- For 20 mm microphones (CMC with capsule)
Microphone Outdoor Protection Consisting of wind shield R1 and W 20 R Wind protection basket W 20 R, Wind noise attenuation at 18 km / h with balls 43 dB-A, with a supercardioid 51 dB-A, Diameter: 90 mm, Colour:...
- Consisting of wind shield R1 and W 20 R Wind protection basket W 20 R
- Wind noise attenuation at 18 km / h with balls 43 dB-A, with a supercardioid 51 dB-A
- Diameter: 90 mm
Stand Joint For active tubes (8mm) and stand tubes (12mm), Angle degree can be changed, Colour: Grey (matt)
- For active tubes (8mm) and stand tubes (12mm)
- Angle degree can be changed
- Colour: Grey (matt)
PopscreenIt is sufficient for medium-to-high speakers to protect the cardioid and other pressure gradient receivers, especially when they are speech microphones. For bullets it is sufficient even in low winds. Very low sound. Dimensions: 70 mm ×...
- Dimensions: 70 mm × Ø 45 mm (max)
- Colour: grey (standard)
Small close-speech guard Made of washable nylon fabric, Wind noise attenuation at 18 km/h with bullet microphones: 25 dB-A, With supercardioid microphones: 26 dB-A, Diameter 50 mm, Colour: Grey, Not suitable for the following types: MK 4V, MK 41V,...
- Made of washable nylon fabric
- Wind noise attenuation at 18 km/h with bullet microphones: 25 dB-A
- With supercardioid microphones: 26 dB-A
Flute adapter Allows the use of a CCM compact microphone on the flute, The FA 1 is a plastic double clip that simply clips onto the mouth end of the flute, The 0° axis of the microphone capsule should...
- Allows the use of a CCM compact microphone on the flute
- The FA 1 is a plastic double clip that simply clips onto the mouth end of the flute
- The 0° axis of the microphone capsule should point to the mouth hole
Stand clamp With joint, With clamp made of grey plastic, For compact microphones
- With joint
- With clamp made of grey plastic
- For compact microphones
Stand Clamp With joint, With metal clamp, For compact microphones
- With joint
- With metal clamp
- For compact microphones
Microphone amplifierThe microphone amplifiers CMC are not (power) amplifiers in the usual sense. Its task is to adapt the signals of the high-impedance capacitor capsule for the very low-impedance, balanced transmission through the microphone cable. The different versions differ by...
- Power supply for 48 V phantom for capsules of the MK series
- Current consumption: 4 mA
- Length: 113 mm
Stand Tube These stand tubes have a 3/8" threaded pin at the top and a 3/8" female thread at the bottom. Therefore, several rods can be screwed together. They also fit into the collets of the bottom leg BF...
- Suitable for BF 250 sockets
- Length: 350 mm
Schoeps SRS 420 C, gooseneck for Schoeps MK-capsule, for installiation on the desk, lenght 420mm, colour:grey
Stand Connection Joint
Stand Connection Joint For connecting two STR stand bars
- For connecting two STR stand bars
WindshieldHighly effective wind shield for pressure gradient and pressure receivers with low sound effects. The foam hollow sphere encloses an air volume around the capsule, similar to a wind protection basket. Particularly when using CCM-L, care must be taken that...
- Dimensions: ball with Ø 90 mm
- Colour: Black
- Additional black flocking
Heavy Base PlateThe BF 250 is supplied complete with the SPV 12-3 / 8 collets for 12 mm diameter stand rods. The tripod rods are fixed by hand with a short rotation of the knurled override. The SPV 12-3 /...
- Including Collets for 12 mm pipes
- Diameter: 250 mm
- Height (without SPV): 38 mm
Schoeps Cut 60, active Low Cut Module for Schoeps Colette Microphe systems, 60 Hz, 24dB/Okt., colour grey, length 17mm
Mostra di più
Le offerte includono il 22% di IVA italiana e sono valide fino ad esaurimento scorte. I costi di trasporto per l´Italia sono di 20 EUR (isole escluse). Per avere maggiori informazioni clicca qui. Non rispondiamo di errori di digitazione o informazioni inadeguate di nessun tipo. *PPC = prezzo al pubblico consigliato dal produttore/distributore in Germania.