Göldo MB05C Adapter Bushings

148

Adapter Bushings for Machine Heads

  • Makes it possible to mount vintage-style machine heads with a shaft diameter of 6.4 mm in a bore hole for enclosed machine heads of 10 mm
  • 6 Pieces
  • MB05C
  • Surface: Nickel
In catalogo dal Luglio 2006
Numero di articolo 193586
Unitá incluse 1 Pezzo
€ 9,90
IVA inclusa,€ 15 di costi di spedizione aggiuntivi
disponibile
disponibile

Questo prodotto è disponibile e può essere spedito immediatamente.

Informazioni sulla spedizione
1

148 Valutazioni dei clienti

4.5 / 5

Devi effettuare il login per poter lasciare una recensione.

IMPORTANTE: Per evitare di inserire informazioni per sentito dire, non complete o sbagliate, permettiamo di dare un giudizio delle attrezzature solo ai nostri clienti che hanno comprato la merce direttamente da noi.

Dopo il Login trovi nella tua area cliente troverete sotto la sezione "Giudica i prodotti" tutti gli articoli ai quali potrete dare un giudizio

Qualità

73 Recensioni

D
Adattatori ok
Dogbone 31.03.2018
Se volete montare delle meccaniche vintage tipo kluson su una paletta con fori grandi (10mm), avrete bisogno di questi adattatori, c'è da dire che alcune chitarre asiatiche hanno fori da 10, 5mm e questi adattatori vanno un po laschi, si può comunque risolvere con un giro di carta o qualche goccia di colla alifatica.
Qualità
0
0
Segnala un abuso

Segnala un abuso

A
Perfette
Anonimo 27.02.2016
Göldo MB05C Adapter Sockets per convertire i fori da 10mm delle meccaniche in 8mm. Esteticamente non sono perfettamente identici ai classici pezzi vintage ma nel complesso donano un ottimo look allo strumento senza risultare inadeguati. Ottimi anche per strumenti vintage, poiché non risultano avere un look troppo moderno
Qualità
0
0
Segnala un abuso

Segnala un abuso

google translate gb
Sfortunatamente si è verificato un errore, La preghiamo di riprovare più tardi.
TO
Great product - Just not the right fit
Tiago Oliveira Coelho 21.07.2020
Bought a set of Klusons for my Classic 60's Tele (MIM) to replace the Kluson-style Ping/Fender stock tuners, but the bushings were too narrow for the pre-existing holes. So I found these conversion bushings and thought my problem was solved.
Before anything, I have to say that they're quite good, and feel very solid. A+ for building quality.

However, the holes for the tuners in my guitar is neither 8mm nor 10mm. If you have the same model as I do, either be prepared to enlarge the holes on the headstock to fit these, or just use aluminium tape on the narrow bushings to keep them in place.
Qualità
0
0
Segnala un abuso

Segnala un abuso

google translate gb
Sfortunatamente si è verificato un errore, La preghiamo di riprovare più tardi.
t
My bad, they didn’t fit…
tremblox 07.01.2023
These are fine but didn’t fit my application. I’m writing this as a heads-up to others.
Firstly not all tuners, even Gotoh tuners have the same post/shaft diameter. Not even in the same series. Take for example the Kluson-style SD91 series. The units with magnum lock and height adjustable post/shafts - the HAP-M units - have 6mm post diameters. They fit too loosely in these bushings and as a result of the string tension the tuners will get sloppy and wear out prematurely over time.
On the other hand the standard SD91 tuners (no locking, height adjustment) have post diameters of ca 6,25mm (from memory so I might be off by a tad), so that these bushings will be a perfect fit and you’ll enjoy a lifetime of happiness with them.

So in all cases the buyer should check their post diameters carefully before selecting and trying to source the correct bushings. Take care, it’s a jungle out there.
Qualità
1
0
Segnala un abuso

Segnala un abuso