• Wish list
  • Choose your store
    All countries
  • 0

3. Media

As the main aim of mastering is the preparation of material for the manufacture and distribution of a mass market medium, we’ll now take a look at the various types of media that the industry has used, past and present, so that we can better understand how the process of mastering came into being.


Until the 80s, vinyl was the dominant consumer medium, and little has changed in this area since the 50s when the first stereo, ‘long playing’ vinyl disks were released.

A vinyl disc

In the studio, tape was the preferred medium, and so the audio from 15ips (inches per second) stereo ¼” tape mixes were transferred and cut by lathe onto a master disk or ‘lacquer’ by the cutting engineer, before making master copies from this for manufacturing. The audio waveform of the song is emulated by the spiral groove cut into a record, and the movement of the stylus follows this. To make sure that the amplitude of the groove ‘wiggle’ is reasonably constant across all audio frequencies, the lower frequencies (below 500Hz) are reduced and the higher frequencies (above 2kHz) are boosted when the groove is cut. This means that when the record is played back, the opposite characteristics must be applied, i.e. the lower frequencies must be boosted and the higher frequencies reduced. This process was first adopted in the late 50s when the Recording Industry Association of America (RIAA) agreed an international standard - this is why the input to an amplifier for a record deck is often termed the ‘RIAA’ input, as it contains the EQ circuit necessary to restore the frequency characteristics of the original audio. Because of the physical limitations of vinyl, it was important for the cutting engineer to make sure that both the EQ and dynamics did not make the record distort or jump when trying to reproduce any large peaks or transients, and it was from this process that the mastering engineer’s role evolved into what it is today.


The compact cassette system was developed by Philips in 1963, originally for recording speech, but it became popular for music once the obstacles of limited bandwidth and poor signal-to-noise ratio had been overcome to a reasonable degree.

The compact cassette

Bandwidth was increased by the use of special magnetic tape formulations, including high-density ferric oxide, chromium dioxide and pure metal compounds. These tapes also allowed signals to be recorded at higher levels, and so went some way to improving the signal to noise ratio, but this issue was only really solved when Dolby Laboratories licensed a consumer version of its noise reduction technology. Their ‘Dolby B’ system dramatically improved the sound quality of compact cassette tapes, enabling them to rival vinyl. The ability to make Dolby encoded home recordings was also a very attractive feature of the system, and certainly contributed to the widespread acceptance of the compact cassette, sales of which overtook vinyl in 1983. This was only short lived though, as both media were usurped by the Compact Disc shortly after.

Compact Discs

With the arrival of the CD, new digital post-production mastering methods were adopted, including the editing of mixes in a DAW (Digital Audio Workstation). The modern procedure involves a finalised master recording being stored on digital media such as an Exabyte 8mm tape cartridge, in the case of an album, along with ‘metadata’ regarding the track separation, track numbers, and track length. From the tape, a ‘glass master’ is created, and from this all subsequent copies are taken to produce the completed CDs you see in the shops.

CDs themselves consist of a clear polycarbonate disc, usually 12cm in diameter and 1.2mm thick. The audio data is pressed into the aluminised reflective side of the disc to form the data layer. This is covered in a coating of protective lacquer, onto which the disc label is printed. To ‘play’ the CD, an infrared laser is focused through the polycarbonate underside to read the audio data stored as ‘pits’ and ‘lands’ (see below) in a spiral track spaced 1.6um apart (1um = one millionth of a metre).

A CDs pits and lands

Although CD is still the dominant consumer media for music, MP3 players such as Apple’s iPod, along with the internet, have provided a way to distribute songs and albums that can cut out the traditional mastering, production and distribution stages. Armed only with ordinary popular sequencing software, you can now mix, master, and upload your material to a website for all to access. Also, low-cost mastering software such as Steinberg’s WaveLab and Apple’s Waveburner enables you to edit and compile your own tracks, as in a mastering studio, and then burn these directly to CD in your computer. Here though, the similarity to the professional mastering process ends, as Exabyte tape is specially formulated to produce virtually no bit-errors, unlike the average CD-R. Even at 1x burning speed, the number of errors can exceed 200 per second, unlike a glass-mastered CD that undergoes bit by bit verification, producing a much more acceptable 20 to 30 errors per second.

Bit-errors aside, doing your own mastering still requires the right knowledge to make use of the tools, and the mastering engineer’s techniques still apply, which we shall consider next. Probably the most important post-production task is the treatment of the overall dynamics of both individual tracks, and whole albums, as the songs may vary in instrumentation and structure, differing greatly in dynamic content. As we have seen, this can then make it difficult to transfer the audio to the final master medium. To overcome this, an engineer will apply gain reduction with a dynamics processor such as a compressor or limiter:

Your Contact People
Phone: +49-9546-9223-35
FAX: +49-9546-9223-24
Phone: +49-9546-9223-30
FAX: +49-9546-922328
Question! Give the right answer and win 1x Thomann Rack Case 6U worth 71 €.
What is not a part of a reverb signal?
Conditions of participation
Terms and Conditions for participation
in online competitions

Note: Participation in an online competition runs independently from any purchase at Thomann GmbH. The following Competition Rules apply when participating in any online competition run by Musikhaus Thomann:

  1. Competition

    1. The competitions are organised by Thomann GmbH, CEO: Hans Thomann, Hans-Thomann-Straße 1, 96138 Burgebrach, Germany.
  2. Participation

    1. Competitions are only open to persons of full age.
    2. To take part in the competition you must answer all questions correctly, fill in the registration form and submit your entry to Thomann GmbH by pressing the "send" button.
      By pressing the "send" button the participant accepts the aforementioned terms and conditions.
    3. The participant is responsible for entering their email and/or postal address correctly. Entries to the competition will be logged electronically.
  3. Qualifying Entrants

    1. Staff of Thomann GmbH and any cooperation partners and their dependants are excluded from participation.
    2. Should these conditions of participation be violated, especially by using illegitimate means, Thomann GmbH reserves the right to exclude persons from the competition. In case of such violations prizes can be withdrawn and claimed back subsequently.
  4. Announcing the winner

    1. The winners will be notified by Thomann GmbH by email or in writing and their names may be published on the homepage www.thomann.de. The winner accepts this form of publication explicitly.
      Should for whatever reason the winner not claim their prize, then a new winner will be drawn.
    2. The prize presented to the winner may not be identical to the item description. There can be deviances regarding the model, colour etc.
    3. The merchandise prizes will be sent by Thomann GmbH or by one of its contracting delivery companies, per freight forwarder, courier or postal service to the postal address indicated by the winner.

      The delivery is free of charge. Only extra transport costs and customs/duties must be covered by the winner. In the case that the delivery has to be made through a freight forwarding company the freight forwarding company will contact the winner to arrange delivery timings.
    4. An exchange, cash alternative or replacement prize is not possible.
    5. The claim to the prize or replacement of the prize cannot be assigned to a third party.
  5. Data protection

    1. The participant accepts explicitly that Thomann GmbH saves all necessary data for the duration of the competition and forwards them exclusively for purposes related to the winning process to the respective cooperation partner, who is also permitted to save the personal data only for the duration of the competition. The participant is free to withdraw his entry at any time. Please direct the withdrawal to:

      Thomann GmbH
      to the data protection officer
      Hans-Thomann-Straße 1
      96138 Burgebrach, Germany
    2. Thomann GmbH is obliged to consider the regulations for data protection according to the Federal Data Protection Law (BDSG) valid at the conclusion of the competition. In this context the general data protection regulations under notes regarding data protection should be noted.
  6. Liability

    1. Thomann GmbH will be released from any obligations by handing out the prize.
    2. Thomann GmbH is not liable for the insolvency of a cooperation partner and the resulting consequences for the implementation and processing of the competition.
  7. Other

    1. Legal proceedings are barred.
    2. The law of the Federal Republic of Germany applies exclusively.
One of our Fans
I wish yourself and the rest of Thomann's staff the very best, and thank you again for seeing to my matter in such good time
nixxxramah@hxxx.com, 20.02.2017

Mastering overview


Found an error or want to give us feedback about this page?

We're looking forward to hearing from you and aim to solve any problems as soon as we can.