UB
P16-D Ultranet distributer
There really isn't much you can say about this device, because it's boring, has no user controls bar an on-off switch, but is an essential part of our system.
In our band, the drummer and I have been on in-ears for a long time. I find I need a very specific mix (too many nasty harmonies) so I bought the P16M for our Behringer system. I'm happy - but the guitarist and keyboard player still make too much noise, and soundchecks were taking too long. In the end, they bought some Behringer small active speakers and attached them to their mic stands, but still soundchecks took too long, with everyone wanting too much, in too short a time. I bought another couple of P16M personal mixers, but discovered that they need powering and that was a bit of a pain.
The P16D Ultranet unit simply lets you connect each P16 mixer with the single cat5 cable. Power is supplied down the cable, making the wiring much, much simpler. Connection wise, the device sits in the rack next to the S16s, and connects to this unit with another Cat5 cable. You turn it on, plug in and there are no controls whatsoever.
The only downside I can think of is that Behringer don't make a rack mount kit - so mine is simple in the rack, gaffer taped to the top of the S16 - a bit of a bodge but fine in practice.
This unit will also connect to other behringer Ultranet devices if you don't have an X32 to drive it.
It's simply a distributer of the Ultranet audio and power.
You cannot use a normal network switch as the Ultranet system supports the DC power system to power the P16M's, and a network switch does not.
Can I recommend it? Of course - it makes wiring so much more simpler than trying to supply mains power near each mixer on stage.
In our band, the drummer and I have been on in-ears for a long time. I find I need a very specific mix (too many nasty harmonies) so I bought the P16M for our Behringer system. I'm happy - but the guitarist and keyboard player still make too much noise, and soundchecks were taking too long. In the end, they bought some Behringer small active speakers and attached them to their mic stands, but still soundchecks took too long, with everyone wanting too much, in too short a time. I bought another couple of P16M personal mixers, but discovered that they need powering and that was a bit of a pain.
The P16D Ultranet unit simply lets you connect each P16 mixer with the single cat5 cable. Power is supplied down the cable, making the wiring much, much simpler. Connection wise, the device sits in the rack next to the S16s, and connects to this unit with another Cat5 cable. You turn it on, plug in and there are no controls whatsoever.
The only downside I can think of is that Behringer don't make a rack mount kit - so mine is simple in the rack, gaffer taped to the top of the S16 - a bit of a bodge but fine in practice.
This unit will also connect to other behringer Ultranet devices if you don't have an X32 to drive it.
It's simply a distributer of the Ultranet audio and power.
You cannot use a normal network switch as the Ultranet system supports the DC power system to power the P16M's, and a network switch does not.
Can I recommend it? Of course - it makes wiring so much more simpler than trying to supply mains power near each mixer on stage.
3
0
Report
NB
Does its job
This unit does its job but make sure you have a few quick blow fuses ready as we know of two of theses units that have blown fuses (located where you plug in the kettle lead) It doesnt take long to change them but lets be honest, you really dont want anything like this happening mid performance. I'm guessing Behringer will sort this for future production runs if the get feedback. Overall though the whole system including desk and personal monitoring is great value for money.
3
0
Report
KB
indispensible Behringer P16D
If you use P16M personal mixers (and you should!) this distribution box supplies signal AND POWER to your units, reducing cabling dramatically and adding reliability,and gives a great central stage distribution! if you use an X32 (and again you should) this is indispensible!
3
0
Report
GH
Allows you to use P16M without external power
This feature alone is worth the money. Rather than daisy chaining your P16Ms, this allows you to use a star formation and provides power to the P16Ms over the cat5 cable. A great upgrade for my system. This will be used in theatres and bands.
0
0
Report
a
i have some problems
p16 stack and we have to remove tha lan and put it again back
0
0
Report
Sd
POE makes easy
Is good you can have less cable to chain with the P16, because is POE, so is no need to have additional power supply for P16, is handly.
0
0
Report
I
A device that is all it is cracked up to be
This is a very basic device which simply allows you to transmit power and data to P16M units with one cable. We have 6 of the P16M units plugged in for my band and have never had any issues with it. A few reviews mention the need for spare fuses but we haven't had any fuses blow since we got it and I don't anticipate any reason it would start blowing fuses now, hopefully it was an issue that Behringer have resolved.
0
0
Report
W
Great device!
Easy to use and does what it's supposed to without any hassle. PLUG & PLAY!!
0
1
Report
M
Great hassle saver
Use this in the studio and the hassle that is saved not having to plug the power supplies into the P16M's is a real bonus. A rack ear kit would be nice...
0
0
Report
P
Great must have with the P16M!!!
Great must have with the P16M!!!
We use this unit for our worshipteam and it's a great addition if youre using the P16 system!
We use this unit for our worshipteam and it's a great addition if youre using the P16 system!
0
0
Report
