Voodoo Lab Voltage Doubling Cable PPY

173

Voltage Doubler Cable

  • Pedals with higher voltage requirements can use this voltage doubler cable to combine two isolated power supply multi-outputs and thus provide 18 V or 24 V
  • Suitable for various MXR Dunlop Fulltone and Keeley pedals
  • Power supply: 2 x 2.1 mm coaxial
  • Pedal connector: 2.1mm coaxial
  • Polarity: Standard (center minus)
  • Length: 46 cm
Myynnissä vuodesta Huhtikuu 2008
Tuotenumero 207270
Myyntierä 1 kappaletta
10,90 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu toimituspäivä Torstai, 25.04. - Perjantai, 26.04.
1

173 Asiakkaiden arviot

4.6 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Työnjälki

73 Arvostelut

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
A
A useful tool
Tuntematon 30.01.2015
I purchased this product to allow a Decibel 11 Hot Stone Deluxe to power a Pigtronix Echolution 2 delay pedal.

The pedal required 18v whereas the power supply was only able to provide 9v.
Despite being made by Voodoo Lab this adapter will work with any power supply which uses the standard Boss style connectors.

It has worked flawlessly in operation and appears to be made to a high standard. I have had no issues with noise etc.

Though it is advertised for use with pedals such as the OCD I would recommend it more for pedals like the Echolution 2 which require both 18v and a significant amount of current.

There are adapters from other manufacturers which will only take up a single output from your power supply and can output 18v however these are typically limited to 30mA and so can only be used with low current pedals.

This cable can also be used to provide 24v by combining two 12v outputs although it won't provide the reverse polarity that some pedals of this voltage require.
Työnjälki
1
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
S
Does what it needs to do
SJS 14.02.2021
I bought this cable as to be able to supply 18v to my Fulltone Supa-Trem2 V2 which can function at this voltage in order to provide more headroom. It works flawlessly.

Pros: High quality as usual in Voodoo Labs products
Cons; None
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
d
Recommended
din65 23.03.2022
Good quality and gets the job done!
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
G
Double your power!
Guitarpower 14.02.2014
I always loved the sound of my Fulltone OCD in front of my Marshall JMP 100 MK2 - but then I asked myself: How good could this combination sound, using the 18-Volt mode of the OCD ...?!
So, I started looking around for a suitable power cable (and power supply) for the OCD! I soon found out that the Voodoo Lab Y - 18 volt cable seems to be the best buy - and what can I say: yes it is!
The 'new' sound of my Fulltone OCD (thanks to the Voodoo Lab cable: now with 'double power' ;-)) is really great!! It is more straight ahead now than it was before!
If you are looking for a good and reasonably priced 18 Volt Cable, dont look any further!
Keep rockin'!!
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta