TAD 500k Push/Pull Poti

46

Push/Pull Potentiometer

  • Logarithmic
  • Long thread
  • With knurled shaft
  • Thanks to the dual switch, many combinations are possible such as series/parallel, out-of-phase, coil tab etc.
  • Diameter: 16 mm (5/8")
  • Thread length: 19 mm (3/4")
  • Required bore diameter: 9.5 mm (3/8")
Myynnissä vuodesta Joulukuu 2013
Tuotenumero 329594
Myyntierä 1 kappaletta
Design Push Pull
Resistance Value 500 kOhms
Characteristic Curve Logarithmic
Thread Length 19,0 mm
Tandem Poti No
Push/Push Push/Pull
Solderless No
shaft type grooved
12,90 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu lähetyspäivä Perjantai, 26.04. mennessä
1

46 Asiakkaiden arviot

4.4 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Työnjälki

25 Arvostelut

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
V
Big solid built push-pull
V_Korneev 09.05.2018
I use one of these for 4+ months and it doesn?t show any signs of deterioration (yet even some cheapest pots can survive that long, so it?s not a clear sign). It works smoothly without any wobbling or scratchy noises. It?s a decent thing for it?s price, but you can get functionally equal pots somewhat cheaper, so decide for yourself if saving a couple of bucks is worth it.

For a guitar with a thin body or for an audio device in a tight casing you would probably prefer smaller pots.
Työnjälki
1
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
R
It works
RyanR 11.04.2015
I got this push-pull pot to install a fuzz-factory circuit into an old Epiphone Explorer 1984. I use it as a volume/ effect on-off switch. Being 500k it works fine with my SH-6 humbuckers. It was easy to solder, smooth to use, seems well built. It is rather large; luckily for me my guitar body is a thick slab of mahogany, thinner guitars may not accommodate this pot.
Työnjälki
1
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
A
Great pots
Anatoly 20.03.2019
Fit perfectly, work perfectly.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
A
Well Built :)
Angelus502 24.04.2015
You know how you can just tell quality when you see and feel a product, well this is one of those. Well built, solid feeling, smooth movement, heavy. I cant tell you how reliable it is as I've only just installed it, but its feels 10 times better than stock pots so i figure it should last.

The long shaft means it only just fits in my PRS. The grooves on the shaft are the course cut.
Työnjälki
1
0
Raportoi ongelmasta

Raportoi ongelmasta