Rockbag Fingerboard Saver Set

195

Fretboard Protector Set

  • For thin, medium and jumbo fret wires
  • Protects the fingerboard from scratches and dents during filing, crowning or polishing the frets
  • Fits most thin fret wires / medium fret wires / jumbo frets wires
  • Fits between all frets on guitars, banjos and electric basses
  • Fits between most frets of ukuleles and mandolins
  • Slot widths: 1.8 mm (5/64") / 2.65 mm (7/64") / 3.15 mm (1/8")
  • Slot length: 70 mm (2 3/4") - fits most 5-string electric basses
  • Notches for fixing with the enclosed rubber bands
  • Made of spring-hardened 0.2 mm (1/64 ") stainless steel
  • Adjusts to the fretboard radius
  • Set consists of 2 pieces including rubber bands and 1 x sanding block (sanding block with 1000 grit)
  • Dimensions Fingerboard Protector (L x W): 80 mm (3 5/32 ") x 16 mm (5/8")
  • Dimensions of sanding block (L x W x H): 100 mm (3 15/16 ") x 10 mm (25/64") x 10 mm (25/64 ")

Note: Also available separately in sets of 2 pieces per slot width.

Myynnissä vuodesta Elokuu 2017
Tuotenumero 419717
Myyntierä 1 kappaletta
Size Small - Medium - Jumbo
Amount 6
9,90 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu toimituspäivä Maanantai, 29.04. - Tiistai, 30.04.
1

195 Asiakkaiden arviot

4.3 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Työnjälki

86 Arvostelut

W
Weebeeji 10.07.2019
Tekee sen mitä pitääkin, kiinnitys kuminauhoilla hieman epäluotettava ainaki HB SC-450 kitaran kaulasasa. Muuten toimi ihan hyvin ,pitää vain olla varovainen ettei suoja lähde paikaltaan.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

R
Great
Rokkipoliisi 27.06.2019
Great way to protect guitar neck when working woth the frets.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
m
Fingerboard Damager not Saver
mjmorrell 07.01.2018
Bought these to protect my fingerboard whilst doing fretwork.
Unfortunately these had the opposite to the desired affect to saving the fingerboard. The metal savers have burrs on the edge and so they cause fine cuts into the fingerboard of my expensive PRS guitar. I then had to sand these out. After noticing this after doing a few frets I stopped using them and went back to using masking tape.
I would advise not using these at all as they may damage your guitar as they did to mine. I would like to know if Thomann or Warwick are going to compensate for the damaged guitar?
Overall not impressed at all, they don't even deserve 1 star since they actually damaged my guitar which I then needed to repair. Waste of money and worse than if they were just useless.
Työnjälki
15
2
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
D
Not that great
DT1980 30.03.2020
I bought these to protect the fingerboard during the polishing of the frets. But these things are so sharp that you have more chance damaging the fretboard than without them. Not practical in use either, a real hassle to put them on the board.
Tried them a few times, but never use them anymore.
Työnjälki
4
0
Raportoi ongelmasta

Raportoi ongelmasta